Metadata: Identification_Information: Citation: Citation_Information: Originator: Amy E. East Originator: Peter Dartnell Publication_Date: 20230901 Title: Grain-size data for sediment samples collected in Whiskeytown Lake, northern California, in 2018 and 2019 Edition: version 2.0 Geospatial_Data_Presentation_Form: comma-delimited text Series_Information: Series_Name: data release Issue_Identification: DOI:10.5066/P9TUTK7J Publication_Information: Publication_Place: Pacific Coastal and Marine Science Center, Santa Cruz, California Publisher: U.S. Geological Survey Online_Linkage: https://doi.org/10.5066/P9TUTK7J Description: Abstract: This data release includes grain-size data from sediment samples collected in submerged and subaerial regions in Whiskeytown Lake and around the reservoir margin. Sediment samples were collected using a sampler deployed from a boat or by hand from locations exposed above the water surface. Sediment grain size was analyzed at the USGS laboratory in Santa Cruz, Calif. The full data set is reported here, but users should be aware that due to instrument error the data between approximately grain sizes from 0.040 to 0.063 mm may be incorrect and have unknown degrees of uncertainty. Proportions of gravel, sand, silt, and ratios among these size fractions, are considered accurate. Purpose: The Carr Fire ignited in northern California in July 2018, and ultimately burned almost 300,000 acres (approximately half on Federal lands), resulting in a federal major-disaster declaration (DR-4382). Approximately 93 percent of the area within Whiskeytown National Recreation Area was burned extensively during the Carr Fire, including all of the landscape surrounding and draining into Whiskeytown Lake. Whiskeytown Lake, a federally managed reservoir, subsequently acted as a sediment trap for material eroded from hillslopes and streambeds in the aftermath of the Carr Fire. The U.S. Geological Survey measured topographic change associated with sediment deposition and erosion in and around Whiskeytown Lake after the Carr Fire, in order to support calculations of post-fire sediment yield from the surrounding landscape. Data collection and analysis have been supported by funds through H.R. 2157, the Additional Supplemental Appropriations for Disaster Relief Act of 2019. Supplemental_Information: Additional information about the field activities from which these data were derived is available online at: https://cmgds.marine.usgs.gov/fan_info.php?fan=2018-686-FA Any use of trade, product, or firm names is for descriptive purposes only and does not imply endorsement by the U.S. Government. Sediment samples from Whiskeytown Lake (within Whiskeytown National Recreation Area) were collected under a Scientific Research and Collection Permit issued by the National Park Service, permit number WHIS-00139. Time_Period_of_Content: Time_Period_Information: Range_of_Dates/Times: Beginning_Date: 20181213 Ending_Date: 20190515 Currentness_Reference: End of sample collection. Status: Progress: Complete Maintenance_and_Update_Frequency: None planned Spatial_Domain: Bounding_Coordinates: West_Bounding_Coordinate: -122.60499716 East_Bounding_Coordinate: -122.51648694 North_Bounding_Coordinate: 40.65396202 South_Bounding_Coordinate: 40.59500793 Keywords: Theme: Theme_Keyword_Thesaurus: ISO 19115 Topic Category Theme_Keyword: geoscientificInformation Theme: Theme_Keyword_Thesaurus: Data Categories for Marine Planning Theme_Keyword: Material Resources Theme_Keyword: Assessments Theme: Theme_Keyword_Thesaurus: USGS Thesaurus Theme_Keyword: land surface characteristics Theme: Theme_Keyword_Thesaurus: Marine Realms Information Bank (MRIB) keywords Theme_Keyword: sediment Theme: Theme_Keyword_Thesaurus: None Theme_Keyword: U.S. Geological Survey Theme_Keyword: USGS Theme_Keyword: Coastal and Marine Hazards and Resources Program Theme_Keyword: CMHRP Theme_Keyword: Pacific Coastal and Marine Science Center Theme_Keyword: PCMSC Theme_Keyword: grain size Theme_Keyword: sediment grain size Theme_Keyword: reservoir sedimentation Theme: Theme_Keyword_Thesaurus: USGS Metadata Identifier Theme_Keyword: USGS:64a31377d34ef77fcb057059 Place: Place_Keyword_Thesaurus: Geographic Names Information System (GNIS) Place_Keyword: Whiskeytown National Recreation Area Place_Keyword: State of California Access_Constraints: None Use_Constraints: USGS-authored or produced data and information are in the public domain from the U.S. Government and are freely redistributable with proper metadata and source attribution. Please recognize and acknowledge the U.S. Geological Survey as the originator(s) of the dataset and in products derived from these data. Point_of_Contact: Contact_Information: Contact_Organization_Primary: Contact_Organization: U.S. Geological Survey, Pacific Coastal and Marine Science Center Contact_Person: PCMSC Science Data Coordinator Contact_Address: Address_Type: mailing and physical Address: 2885 Mission Street City: Santa Cruz State_or_Province: CA Postal_Code: 95060 Contact_Voice_Telephone: 831-460-7401 Contact_Electronic_Mail_Address: pcmsc_data@usgs.gov Browse_Graphic: Browse_Graphic_File_Name: https://www.sciencebase.gov/catalog/file/get/ 64a31377d34ef77fcb057059?name=Whiskeytown_Grainsize_map.jpg&allowOpen=true Browse_Graphic_File_Description: Map showing location of samples collected for grain-size analysis. Browse_Graphic_File_Type: JPEG Native_Data_Set_Environment: MacOS 10.14.6 running Microsoft Excel v. 16.47.1 Cross_Reference: Citation_Information: Originator: Peter Dartnell Publication_Date: 2021 Title: Chirp sub-bottom data collected in 2019 in Whiskeytown Lake, California during USGS field activity 2018-686-FA Other_Citation_Details: Dartnell, P., Brothers, D.S., East, A.E., Currie, J., Dal Ferro, P., and Logan, J.B., 2021, Chirp sub-bottom data collected in 2019 in Whiskeytown Lake, California during USGS field activity 2018-686-FA: U.S. Geological Survey data release. Online_Linkage: https://doi.org/10.5066/P958Q0DX Cross_Reference: Citation_Information: Originator: Joshua B. Logan Publication_Date: 2020 Title: Bathymetry, topography and orthomosaic imagery for Whiskeytown Lake, northern California Other_Citation_Details: Logan, J.B., Dartnell, P., East, A.E., and Ritchie, A.C., 2020, Bathymetry, topography and orthomosaic imagery for Whiskeytown Lake, northern California: U.S. Geological Survey data release. Online_Linkage: https://doi.org/10.5066/P9HEDYNT Cross_Reference: Citation_Information: Originator: Robert Louis Folk Originator: William C. Ward Publication_Date: 1957 Title: Brazos River bar; a study in the significance of grain size parameters Other_Citation_Details: Folk, R.L., and Ward, W.C., 1957, Brazos River bar; a study in the significance of grain size parameters: Journal of Sedimentary Research, v. 27, n. 1, p. 3-26. Online_Linkage: https://doi.org/10.1306/74D70646-2B21-11D7-8648000102C1865D Cross_Reference: Citation_Information: Originator: Douglas Lamar Inman Publication_Date: 1952 Title: Measures for describing the size distribution of sediments Other_Citation_Details: Inman, D.L., 1952, Measures for describing the size distribution of sediments: Journal of Sedimentary Research, v. 22, n. 3, p. 125-145. Online_Linkage: https://doi.org/10.1306/D42694DB-2B26-11D7-8648000102C1865D Cross_Reference: Citation_Information: Originator: Parker D. Trask Publication_Date: 1930 Title: Mechanical analyses of sediments by centrifuge Other_Citation_Details: Trask, P.D., 1930, Mechanical analyses of sediments by centrifuge: Economic Geology, v. 26, n. 6, p. 581-599. Online_Linkage: https://doi.org/10.2113/gsecongeo.25.6.581 Data_Quality_Information: Attribute_Accuracy: Attribute_Accuracy_Report: Several months after the samples were analyzed, a problem was discovered with the LPSA that had caused inaccurate measurement of the coarse silt content (sizes approximately from 0.040 to 0.063 mm). Grain-size distribution of particles coarser than 0.063 mm is thought to have been unaffected, and the proportions of silt (0.040 to 0.063 mm) and clay (finer than 0.004 mm) also were thought to have been measured accurately. The full data set is reported here, but users should be aware that due to this instrument error the data between approximately grain sizes from 0.040 to 0.063 mm may be over-estimated and have unknown degrees of uncertainty. Proportions of gravel, sand, silt, and ratios among these size fractions, are considered accurate. Logical_Consistency_Report: No formal logical accuracy tests were conducted. Data values are within the expected values. Completeness_Report: Dataset is considered complete for the information presented, as described in the abstract. Users are advised to read the rest of the metadata record carefully for additional details. Positional_Accuracy: Horizontal_Positional_Accuracy: Horizontal_Positional_Accuracy_Report: Horizontal positional accuracy is estimated to be that of the navigation system on the R/V San Lorenzo, the vessel from which samples were collected. On this vessel, the Applanix POS-MV post-processed horizontal positional accuracy is about 0.1 m with roll and pitch accuracies of about 0.02 degrees (https://www.applanix.com/downloads/products/specs/posmv/POS-MV-WaveMaster-II.pdf). The SWATHPlus sonar system has an across-track resolution of about 5 cm (http://www.bathyswath.com/sites/default/files/documents/ETD_2002_Bathyswath%20information_EN.pdf). Accuracies of final products may be lower due to total propagated uncertainties of the mapping systems, which include sonar system, position and motion compensation system, and navigation, as well as data processing that includes sounding cleaning, gridding, and datum transformations. Lineage: Process_Step: Process_Description: Sediment grain size was analyzed at the USGS laboratory in Santa Cruz, Calif. Particles coarser than 2 mm were sieved using a RO-TAP sieve shaker, and particles finer than 2 mm were analyzed with a Coulter laser particle-size analyzer (LPSA), after organic matter had been removed using a hydrogen peroxide solution. Several months after the samples were analyzed, a problem was discovered with the LPSA that had caused inaccurate measurement of the coarse silt content (sizes approximately 0.040 to 0.063 mm). Grain-size distribution of particles coarser than 0.063 mm was unaffected, and the proportions of silt (0.040 to 0.063 mm) and clay (finer than 0.004 mm) also were measured accurately. The full data set is reported here, but users should be aware that due to this instrument error the data between grain sizes 0.040 and 0.063 mm may be over-estimated and have uncertainty of approximately 20%. Process_Date: 2019 Process_Contact: Contact_Information: Contact_Person_Primary: Contact_Person: Angela Tan Contact_Organization: U.S. Geological Survey, Pacific Coastal and Marine Science Center Contact_Position: Sediment Laboratory Manager Contact_Address: Address_Type: Mailing, physical Address: 2885 Mission Street City: Santa Cruz State_or_Province: CA Postal_Code: 95060 Contact_Voice_Telephone: 831-460-4747 Contact_Electronic_Mail_Address: atan@usgs.gov Process_Step: Process_Description: INTERPOLATED SIZES WITH COLUMN HEADING CORRECTION: Grain sizes at select cumulative percentage values (D) were calculated by the PCMSC Sediment Lab software pcSDSZ version 2.00 using a polynomial interpolation between phi bins bracketing the specified D value. Grain sizes were converted into units of millimeters (mm) using the formula mm=reciprocal of 2(exponent)phi. Grain sizes at D5, D10, D16, D25, D50, D75. D84, D90, and D95 are reported in phi and millimeter units. PCMSC Sediment Lab data reports issued between February 2011 and August 2022 were revised so that the column headers for the Interpolated Sizes in millimeter units (mm) were transposed from increasing to decreasing D values to correctly reflect the columns of data. This revised metadata shows the column heading correction, which also appears in the corresponding revised data table. Process_Date: 20230627 Process_Contact: Contact_Information: Contact_Person_Primary: Contact_Person: Angela Tan Contact_Organization: U.S. Geological Survey, SOUTHWEST REGION Contact_Position: Physical Scientist Contact_Address: Address_Type: mailing address Address: 2885 Mission Street City: Santa Cruz State_or_Province: CA Postal_Code: 95060 Country: US Contact_Voice_Telephone: 831-460-7409 Contact_Facsimile_Telephone: 831-427-4748 Contact_Electronic_Mail_Address: atan@usgs.gov Spatial_Data_Organization_Information: Direct_Spatial_Reference_Method: Point Point_and_Vector_Object_Information: SDTS_Terms_Description: SDTS_Point_and_Vector_Object_Type: Point Point_and_Vector_Object_Count: 56 Spatial_Reference_Information: Horizontal_Coordinate_System_Definition: Geographic: Latitude_Resolution: 0.000001 Longitude_Resolution: 0.000001 Geographic_Coordinate_Units: Decimal degrees Geodetic_Model: Horizontal_Datum_Name: WGS_1984 Ellipsoid_Name: WGS_1984 Semi-major_Axis: 6378137.0 Denominator_of_Flattening_Ratio: 298.257223563 Entity_and_Attribute_Information: Detailed_Description: Entity_Type: Entity_Type_Label: Attribute table Entity_Type_Definition: Table containing attribute information associated with the dataset. NA indicates that a sediment sample was not analyzed for that grain size, or that the data field was not used, or that no value was calculated. Entity_Type_Definition_Source: Producer defined Attribute: Attribute_Label: FAN ID Attribute_Definition: Unique U.S. Geological Survey field activity identifier Attribute_Definition_Source: producer defined Attribute_Domain_Values: Unrepresentable_Domain: Unique identifier for the U.S. Geological Survey field activity Attribute: Attribute_Label: Sample ID Attribute_Definition: Name of sample Attribute_Definition_Source: producer defined Attribute_Domain_Values: Unrepresentable_Domain: Unique identifier for the sample given in the field Attribute: Attribute_Label: Lab ID Attribute_Definition: Laboratory identification number Attribute_Definition_Source: Producer defined Attribute_Domain_Values: Unrepresentable_Domain: Unique identifier for the sample given during analysis in the lab Attribute: Attribute_Label: Date Collected Attribute_Definition: Date of sample collection in yyyy-mm-dd format Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 2018-12-13 Range_Domain_Maximum: 2019-05-15 Attribute_Units_of_Measure: Dates in yyyy-mm-dd format Attribute: Attribute_Label: Sample Recorded Attribute_Definition: Additional information noted about whether the sample was recorded. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Unrepresentable_Domain: free text section Attribute: Attribute_Label: Time (PDT) Attribute_Definition: Time the sample was collected, in Pacific Daylight Time (PDT). NA indicates no time was noted. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: NA Range_Domain_Maximum: NA Attribute_Units_of_Measure: Time in HH:MM:SS Attribute: Attribute_Label: Description Attribute_Definition: Additional information noted about a sample. NA indicates no additional information was noted. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Unrepresentable_Domain: free text section Attribute: Attribute_Label: Latitude Attribute_Definition: Latitude of sample in decimal degrees Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 40.618647 Range_Domain_Maximum: 40.650496 Attribute_Units_of_Measure: decimal degrees Attribute: Attribute_Label: Longitude Attribute_Definition: Longitude of sample in decimal degrees Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: -122.589960 Range_Domain_Maximum: -122.545234 Attribute_Units_of_Measure: decimal degrees Attribute: Attribute_Label: Sample Type Attribute_Definition: Type of sample collected Attribute_Definition_Source: Producer defined Attribute_Domain_Values: Enumerated_Domain: Enumerated_Domain_Value: Surface grab sample Enumerated_Domain_Value_Definition: Sample collected by hand from the land surface or by Van Veen grab sampler from boat (R/V San Lorenzo). Enumerated_Domain_Value_Definition_Source: Producer defined Attribute: Attribute_Label: Processing notes Attribute_Definition: Notes associated with sample or processing. NA indicates no additional information was noted. Attribute_Definition_Source: Producer defined Attribute_Domain_Values: Enumerated_Domain: Enumerated_Domain_Value: insufficient sand fraction for analysis or used entire sample Enumerated_Domain_Value_Definition: Sample contained insufficient sand for analysis Enumerated_Domain_Value_Definition_Source: Producer defined Attribute_Domain_Values: Enumerated_Domain: Enumerated_Domain_Value: insufficient sand fraction to coulter Enumerated_Domain_Value_Definition: Sample contained insufficient sand to run through the Coulter analyzer Enumerated_Domain_Value_Definition_Source: Producer defined Attribute_Domain_Values: Enumerated_Domain: Enumerated_Domain_Value: used entire sample Enumerated_Domain_Value_Definition: The entire sample was used for processing the first time. Replicate analyses could not be performed to correct for inaccurate analyses. See Attribute Accuracy section of metadata for further explanation. Enumerated_Domain_Value_Definition_Source: Producer defined Attribute: Attribute_Label: Wt. percent in -4.00 phi bin or 16 mm bin Attribute_Definition: Weight percent of sample with grain diameter greater than -4.00 phi, or 16 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in -3.75 phi bin or 13.5 mm bin Attribute_Definition: Weight percent of sample with grain diameter between -4.00 and -3.75 phi, or 13.5 and 16 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in -3.50 phi bin or 11.2 mm bin Attribute_Definition: Weight percent of sample with grain diameter between -3.75 and -3.50 phi, or 11.2 and 13.5 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in -3.25 phi bin or 9.51 mm bin Attribute_Definition: Weight percent of sample with grain diameter between -3.50 and -3.25 phi, or 9.51 and 11.2 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in -3.00 phi bin or 8 mm bin Attribute_Definition: Weight percent of sample with grain diameter between -3.25 and -3.00 phi, or 8 and 9.51 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in -2.75 phi bin or 6.73 mm bin Attribute_Definition: Weight percent of sample with grain diameter between -3.00 and -2.75 phi, or 6.73 and 8 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in -2.50 phi bin or 5.66 mm bin Attribute_Definition: Weight percent of sample with grain diameter between -2.75 and -2.50 phi, or 5.66 and 6.73 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in -2.25 phi bin or 4.76 mm bin Attribute_Definition: Weight percent of sample with grain diameter between -2.50 and -2.25 phi, or 4.76 and 5.66 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in -2.00 phi bin or 4 mm bin Attribute_Definition: Weight percent of sample with grain diameter between -2.25 and -2.00 phi, or 4 and 4.76 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in -1.75 phi bin or 3.36 mm bin Attribute_Definition: Weight percent of sample with grain diameter between -2.00 and -1.75 phi, or 3.36 and 4 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in -1.50 phi bin or 2.83 mm bin Attribute_Definition: Weight percent of sample with grain diameter between -1.75 and -1.50 phi, or 2.83 and 3.36 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in -1.25 phi bin or 2.38 mm bin Attribute_Definition: Weight percent of sample with grain diameter between -1.50 and -1.25 phi, or 2.38 and 2.83 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in -1.00 phi bin or 2 mm bin Attribute_Definition: Weight percent of sample with grain diameter between -1.25 and -1.00 phi, or 2 and 2.38 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in -0.75 phi bin or 1.68 mm bin Attribute_Definition: Weight percent of sample with grain diameter between -1.00 and -0.75 phi, or 1.68 and 2 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in -0.50 phi bin or 1.41 mm bin Attribute_Definition: Weight percent of sample with grain diameter between -0.75 and -0.50 phi, or 1.41 and 1.68 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in -0.25 phi bin or 1.19 mm bin Attribute_Definition: Weight percent of sample with grain diameter between -0.50 and -0.25 phi, or 1.19 and 1.41 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 0.00 phi bin or 1 mm bin Attribute_Definition: Weight percent of sample with grain diameter between -0.25 and 0.00 phi, or 1 and 1.19 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 0.25 phi bin or 0.8409 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 0.00 and 0.25 phi, or 0.8409 and 1 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 0.50 phi bin or 0.7071 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 0.25 and 0.50 phi, or 0.7071 and 0.8409 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 0.75 phi bin or 0.5946 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 0.50 and 0.75 phi, or 0.5946 and 0.7071 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 1.00 phi bin or 0.5 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 0.75 and 1.00 phi, or 0.5 and 0.5946 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 1.25 phi bin or 0.4204 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 1.00 and 1.25 phi, or 0.4204 and 0.5 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 1.50 phi bin or 0.3536 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 1.25 and 1.50 phi, or 0.3536 and 0.4204 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 1.75 phi bin or 0.2973 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 1.50 and 1.75 phi, or 0.2973 and 0.3536 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 2.00 phi bin or 0.25 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 1.75 and 2.00 phi, or 0.25 and 0.2973 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 2.25 phi bin or 0.2102 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 2.00 and 2.25 phi, or 0.2102 and 0.25 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 2.50 phi bin or 0.1768 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 2.25 and 2.50 phi, or 0.1768 and 0.2102 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 2.75 phi bin or 0.1487 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 2.50 and 2.75 phi, or 0.1487 and 0.1768 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 3.00 phi bin or 0.125 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 2.75 and 3.00 phi, or 0.125 and 0.1487 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 3.25 phi bin or 0.1051 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 3.00 and 3.25 phi, or 0.1051 and 0.125 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 3.50 phi bin or 0.08839 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 3.25 and 3.50 phi, or 0.08839 and 0.1051 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 3.75 phi bin or 0.07433 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 3.50 and 3.75 phi, or 0.07433 and 0.08839 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 4.00 phi bin or 0.0625 mm bin, approximate Attribute_Definition: Weight percent of sample with grain diameter between 3.75 and 4.00 phi, or 0.0625 and 0.07433 mm. Values may have been affected by lab equipment malfunction; see section Attribute_Accuracy_Report. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 4.25 phi bin or 0.052556 mm bin, approximate Attribute_Definition: Weight percent of sample with grain diameter between 4.00 and 4.25 phi, or 0.052556 and 0.0625 mm. Values may have been affected by lab equipment malfunction; see section Attribute_Accuracy_Report. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 4.50 phi bin or 0.044194 mm bin, approximate Attribute_Definition: Weight percent of sample with grain diameter between 4.25 and 4.50 phi, or 0.044194 and 0.052556 mm. Values may have been affected by lab equipment malfunction; see section Attribute_Accuracy_Report. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 4.75 phi bin or 0.037163 mm bin, approximate Attribute_Definition: Weight percent of sample with grain diameter between 4.50 and 4.75 phi, or 0.037163 and 0.044194 mm. Values may have been affected by lab equipment malfunction; see section Attribute_Accuracy_Report. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 5.00 phi bin or 0.03125 mm bin, approximate Attribute_Definition: Weight percent of sample with grain diameter between 4.75 and 5.00 phi, or 0.03125 and 0.037163 mm. Values may have been affected by lab equipment malfunction; see section Attribute_Accuracy_Report. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 5.25 phi bin or 0.02628 mm bin, approximate Attribute_Definition: Weight percent of sample with grain diameter between 5.00 and 5.25 phi, or 0.02628 and 0.03125 mm. Values may have been affected by lab equipment malfunction; see section Attribute_Accuracy_Report. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 5.50 phi bin or 0.0221 mm bin, approximate Attribute_Definition: Weight percent of sample with grain diameter between 5.25 and 5.50 phi, or 0.0221 and 0.02628 mm. Values may have been affected by lab equipment malfunction; see section Attribute_Accuracy_Report. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 5.75 phi bin or 0.01858 mm bin, approximate Attribute_Definition: Weight percent of sample with grain diameter between 5.50 and 5.75 phi, or 0.01858 and 0.0221 mm. Values may have been affected by lab equipment malfunction; see section Attribute_Accuracy_Report. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 6.00 phi bin or 0.01563 mm bin, approximate Attribute_Definition: Weight percent of sample with grain diameter between 5.75 and 6.00 phi, or 0.01563 and 0.01858 mm. Values may have been affected by lab equipment malfunction; see section Attribute_Accuracy_Report. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 6.25 phi bin or 0.01314 mm bin, approximate Attribute_Definition: Weight percent of sample with grain diameter between 6.00 and 6.25 phi, or 0.01314 and 0.01563 mm. Values may have been affected by lab equipment malfunction; see section Attribute_Accuracy_Report. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 6.50 phi bin or 0.01105 mm bin, approximate Attribute_Definition: Weight percent of sample with grain diameter between 6.25 and 6.50 phi, or 0.01105 and 0.01314 mm. Values may have been affected by lab equipment malfunction; see section Attribute_Accuracy_Report. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 6.75 phi bin or 0.00929 mm bin, approximate Attribute_Definition: Weight percent of sample with grain diameter between 6.50 and 6.75 phi, or 0.00929 and 0.01105 mm. Values may have been affected by lab equipment malfunction; see section Attribute_Accuracy_Report. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 7.00 phi bin or 0.00781 mm bin, approximate Attribute_Definition: Weight percent of sample with grain diameter between 6.75 and 7.00 phi, or 0.00781 and 0.00929 mm. Values may have been affected by lab equipment malfunction; see section Attribute_Accuracy_Report. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 7.25 phi bin or 0.00657 mm bin, approximate Attribute_Definition: Weight percent of sample with grain diameter between 7.00 and 7.25 phi, or 0.00657 and 0.00781 mm. Values may have been affected by lab equipment malfunction; see section Attribute_Accuracy_Report. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 7.50 phi bin or 0.00552 mm bin, approximate Attribute_Definition: Weight percent of sample with grain diameter between 7.25 and 7.50 phi, or 0.00552 and 0.00657 mm. Values may have been affected by lab equipment malfunction; see section Attribute_Accuracy_Report. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 7.75 phi bin or 0.00465 mm bin, approximate Attribute_Definition: Weight percent of sample with grain diameter between 7.50 and 7.75 phi, or 0.00465 and 0.00552 mm. Values may have been affected by lab equipment malfunction; see section Attribute_Accuracy_Report. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 8.00 phi bin or 0.00391 mm bin, approximate Attribute_Definition: Weight percent of sample with grain diameter between 7.75 and 8.00 phi, or 0.00391 and 0.00465 mm. Values may have been affected by lab equipment malfunction; see section Attribute_Accuracy_Report. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 8.25 phi bin or 0.00329 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 8.00 and 8.25 phi, or 0.00329 and 0.00391 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 8.50 phi bin or 0.00276 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 8.25 and 8.50 phi, or 0.00276 and 0.00329 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 8.75 phi bin or 0.00232 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 8.50 and 8.75 phi, or 0.00232 and 0.00276 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 9.00 phi bin or 0.00195 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 8.75 and 9.00 phi, or 0.00195 and 0.00232 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 9.25 phi bin or 0.00164 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 9.00 and 9.25 phi, or 0.00164 and 0.00195 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 9.50 phi bin or 0.00138 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 9.25 and 9.50 phi, or 0.00138 and 0.00164 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 9.75 phi bin or 0.00116 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 9.50 and 9.75 phi, or 0.00116 and 0.00138 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 9.99 phi bin or 0.00098 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 9.75 and 9.99 phi, or 0.00098 and 0.00116 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 10.25 phi bin or 0.00082 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 9.99 and 10.25 phi, or 0.00082 and 0.00098 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 10.50 phi bin or 0.00069 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 10.25 and 10.50 phi, or 0.00069 and 0.00082 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 10.75 phi bin or 0.00058 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 10.50 and 10.75 phi, or 0.00058 and 0.00069 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 10.99 phi bin or 0.00049 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 10.75 and 10.99 phi, or 0.00049 and 0.00058 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 11.25 phi bin or 0.0004 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 10.99 and 11.25 phi, or 0.0004 and 0.00049 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 11.48 phi bin or 0.00035 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 11.25 and 11.48 phi, or 0.00035 and 0.0004 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 12.02 phi bin or 0.000241 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 11.48 and 12.02 phi, or 0.000241 and 0.00035 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Wt. percent in 13.02 phi bin or 0.00012 mm bin Attribute_Definition: Weight percent of sample with grain diameter between 12.02 and 13.02 phi, or 0.00012 and 0.000241 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Percent Gravel Attribute_Definition: percent of sample greater than 2 mm. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Percent Sand Attribute_Definition: percent of sample less than 2 mm and greater than 63 microns. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Percent Silt Attribute_Definition: percent of sample less than 63 microns and greater than 4 microns. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Percent Clay Attribute_Definition: percent of sample less than 4 microns. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Percent Mud Attribute_Definition: percent of sample less than 63 microns. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 100 Attribute_Units_of_Measure: percentage Attribute: Attribute_Label: Gravel to Sand Ratio Attribute_Definition: ratio of percent gravel in sample to percent sand. NA indicates there was insufficient gravel or sand to compute the ratio. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 12.308 Attribute_Units_of_Measure: no unit Attribute: Attribute_Label: Sand to Silt Ratio Attribute_Definition: ratio of percent sand in sample to percent silt. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 17.574 Attribute_Units_of_Measure: no unit Attribute: Attribute_Label: Silt to Clay Ratio Attribute_Definition: ratio of percent silt in sample to percent clay. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0.901 Range_Domain_Maximum: 11.844 Attribute_Units_of_Measure: no unit Attribute: Attribute_Label: Sand to Clay Ratio Attribute_Definition: ratio of percent sand in sample to percent clay. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 141.859 Attribute_Units_of_Measure: no unit Attribute: Attribute_Label: Sand to Mud Ratio Attribute_Definition: ratio of percent sand in sample to percent mud. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 15.636 Attribute_Units_of_Measure: no unit Attribute: Attribute_Label: Gravel to Mud Ratio Attribute_Definition: ratio of percent gravel in sample to percent mud. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 115.465 Attribute_Units_of_Measure: no unit Attribute: Attribute_Label: D5 Phi Attribute_Definition: Phi size at D5 for sample. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: -4 Range_Domain_Maximum: 6.455 Attribute_Units_of_Measure: Phi size Attribute: Attribute_Label: D10 Phi Attribute_Definition: Phi size at D10 for sample. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: -4 Range_Domain_Maximum: 6.602 Attribute_Units_of_Measure: Phi size Attribute: Attribute_Label: D16 Phi Attribute_Definition: Phi size at D16 for sample. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: -4 Range_Domain_Maximum: 6.817 Attribute_Units_of_Measure: Phi size Attribute: Attribute_Label: D25 Phi Attribute_Definition: Phi size at D25 for sample. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: -4 Range_Domain_Maximum: 7.172 Attribute_Units_of_Measure: Phi size Attribute: Attribute_Label: D50 Phi Attribute_Definition: Phi size at D50 for sample. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: -4 Range_Domain_Maximum: 8.101 Attribute_Units_of_Measure: Phi size Attribute: Attribute_Label: D75 Phi Attribute_Definition: Phi size at D75 for sample. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: -4 Range_Domain_Maximum: 9.217 Attribute_Units_of_Measure: Phi size Attribute: Attribute_Label: D84 Phi Attribute_Definition: Phi size at D84 for sample. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: -4 Range_Domain_Maximum: 9.73 Attribute_Units_of_Measure: Phi size Attribute: Attribute_Label: D90 Phi Attribute_Definition: Phi size at D90 for sample. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: -1.66 Range_Domain_Maximum: 10.127 Attribute_Units_of_Measure: Phi size Attribute: Attribute_Label: D95 Phi Attribute_Definition: Phi size at D95 for sample. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0.969 Range_Domain_Maximum: 10.529 Attribute_Units_of_Measure: Phi size Attribute: Attribute_Label: D95 mm Attribute_Definition: mm size at D5 for sample. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0.0007 Range_Domain_Maximum: 0.5108 Attribute_Units_of_Measure: millimeters Attribute: Attribute_Label: D90 mm Attribute_Definition: mm size at D10 for sample. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0.0009 Range_Domain_Maximum: 3.1598 Attribute_Units_of_Measure: millimeters Attribute: Attribute_Label: D84 mm Attribute_Definition: mm size at D16 for sample. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0.0012 Range_Domain_Maximum: 16 Attribute_Units_of_Measure: millimeters Attribute: Attribute_Label: D75 mm Attribute_Definition: mm size at D25 for sample. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0.0017 Range_Domain_Maximum: 16 Attribute_Units_of_Measure: millimeters Attribute: Attribute_Label: D50 mm Attribute_Definition: mm size at D50 for sample. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0.0036 Range_Domain_Maximum: 16 Attribute_Units_of_Measure: millimeters Attribute: Attribute_Label: D25 mm Attribute_Definition: mm size at D75 for sample. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0.0069 Range_Domain_Maximum: 16 Attribute_Units_of_Measure: millimeters Attribute: Attribute_Label: D16 mm Attribute_Definition: mm size at D84 for sample. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0.0089 Range_Domain_Maximum: 16 Attribute_Units_of_Measure: millimeters Attribute: Attribute_Label: D10 mm Attribute_Definition: mm size at D90 for sample. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0.0103 Range_Domain_Maximum: 16 Attribute_Units_of_Measure: millimeters Attribute: Attribute_Label: D5 mm Attribute_Definition: mm size at D95 for sample. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0.0114 Range_Domain_Maximum: 16 Attribute_Units_of_Measure: millimeters Attribute: Attribute_Label: F-W Median Phi Attribute_Definition: Phi size median for sample by Folk and Ward (1957) method. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: -4 Range_Domain_Maximum: 8.101378 Attribute_Units_of_Measure: Phi size Attribute: Attribute_Label: F-W Mean Phi Attribute_Definition: Phi size mean for sample by Folk and Ward (1957) method. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: -4 Range_Domain_Maximum: 8.216092 Attribute_Units_of_Measure: Phi size Attribute: Attribute_Label: F-W Sorting Phi Attribute_Definition: sorting for sample by Folk and Ward (1957) method. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0.752923 Range_Domain_Maximum: 3.072098 Attribute_Units_of_Measure: Phi size Attribute: Attribute_Label: F-W Skewness Phi Attribute_Definition: skewness for sample by Folk and Ward (1957) method. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: -0.271127 Range_Domain_Maximum: 0.5 Attribute_Units_of_Measure: Phi size Attribute: Attribute_Label: F-W Kurtosis Phi Attribute_Definition: kurtosis for sample by Folk and Ward (1957) method. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 1.474163 Attribute_Units_of_Measure: Phi size Attribute: Attribute_Label: Inman Median Phi Attribute_Definition: Phi size median for sample by Inman (1952) method. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: -4 Range_Domain_Maximum: 8.101378 Attribute_Units_of_Measure: Phi size Attribute: Attribute_Label: Inman Mean Phi Attribute_Definition: Phi size mean for sample by Inman (1952) method. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: -4 Range_Domain_Maximum: 8.273449 Attribute_Units_of_Measure: Phi size Attribute: Attribute_Label: Inman Sorting Phi Attribute_Definition: sorting for sample by Inman (1952) method. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0. Range_Domain_Maximum: 3.13833 Attribute_Units_of_Measure: Phi size Attribute: Attribute_Label: Inman Skew 16-84 Phi Attribute_Definition: skewness for sample (D16-D84) by Inman (1952) method. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: -0.337395 Range_Domain_Maximum: 0.505835 Attribute_Units_of_Measure: Phi size Attribute: Attribute_Label: Inman Skew 05-95 Phi Attribute_Definition: skewness for sample (D05-D95) by Inman (1952) method. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: -0.736325 Range_Domain_Maximum: 0.928505 Attribute_Units_of_Measure: Phi size Attribute: Attribute_Label: Inman Kurtosis Phi Attribute_Definition: kurtosis for sample by Inman (1952) method. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 1.560648 Attribute_Units_of_Measure: Phi size Attribute: Attribute_Label: Trask Median mm Attribute_Definition: mm size median for sample by Trask (1930) method. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0.003641 Range_Domain_Maximum: 16 Attribute_Units_of_Measure: millimeters Attribute: Attribute_Label: Trask Mean mm Attribute_Definition: mm size mean for sample by Trask (1930) method. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0.004308 Range_Domain_Maximum: 16 Attribute_Units_of_Measure: millimeters Attribute: Attribute_Label: Trask Sorting mm Attribute_Definition: sorting for sample by Trask (1930) method. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 1 Range_Domain_Maximum: 5.816288 Attribute_Units_of_Measure: millimeters Attribute: Attribute_Label: Trask Skewness mm Attribute_Definition: skewness for sample by Trask (1930) method. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0.562091 Range_Domain_Maximum: 4.966509 Attribute_Units_of_Measure: millimeters Attribute: Attribute_Label: Trask Kurtosis mm Attribute_Definition: kurtosis for sample by Trask (1930) method. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0 Range_Domain_Maximum: 0.355236 Attribute_Units_of_Measure: millimeters Attribute: Attribute_Label: Mean Phi Attribute_Definition: phi size mean for sample. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: -3.421769 Range_Domain_Maximum: 8.232986 Attribute_Units_of_Measure: Phi size Attribute: Attribute_Label: Mean mm Attribute_Definition: mm size mean for sample. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 0.003324 Range_Domain_Maximum: 10.716556 Attribute_Units_of_Measure: millimeters Attribute: Attribute_Label: Variance Phi Attribute_Definition: variance for sample. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 1.653984 Range_Domain_Maximum: 8.427472 Attribute_Units_of_Measure: Phi size Attribute: Attribute_Label: Std. Dev. Phi Attribute_Definition: standard deviation for sample. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 1.286073 Range_Domain_Maximum: 2.903011 Attribute_Units_of_Measure: Phi size Attribute: Attribute_Label: Skewness Phi Attribute_Definition: skewness for sample. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: -1.763571 Range_Domain_Maximum: 3.523449 Attribute_Units_of_Measure: Phi size Attribute: Attribute_Label: Kurtosis Phi Attribute_Definition: kurtosis for sample. Attribute_Definition_Source: producer defined Attribute_Domain_Values: Range_Domain: Range_Domain_Minimum: 1.876756 Range_Domain_Maximum: 16.953721 Attribute_Units_of_Measure: Phi size Overview_Description: Entity_and_Attribute_Overview: The first line of the csv file is a header line. Entity_and_Attribute_Detail_Citation: U.S. Geological Survey Distribution_Information: Distributor: Contact_Information: Contact_Organization_Primary: Contact_Organization: U.S. Geological Survey - ScienceBase Contact_Address: Address_Type: mailing and physical Address: Denver Federal Center, Building 810, Mail Stop 302 City: Denver State_or_Province: CO Postal_Code: 80225 Contact_Voice_Telephone: 1-888-275-8747 Contact_Electronic_Mail_Address: sciencebase@usgs.gov Resource_Description: These data are available in csv format (Whiskeytown_GrainSize_v2.csv) accompanied by CSDGM FGDC-compliant metadata. Distribution_Liability: Unless otherwise stated, all data, metadata and related materials are considered to satisfy the quality standards relative to the purpose for which the data were collected. Although these data and associated metadata have been reviewed for accuracy and completeness and approved for release by the U.S. Geological Survey (USGS), no warranty expressed or implied is made regarding the display or utility of the data on any other system or for general or scientific purposes, nor shall the act of distribution constitute any such warranty. Standard_Order_Process: Digital_Form: Digital_Transfer_Information: Format_Name: comma-delimited text Format_Version_Number: Excel v. 16.47.1 Format_Information_Content: Sediment grain-size analyses data presented in comma-delimited format (csv) along with CSDGM FGDC-compliant metadata File_Decompression_Technique: No compression applied Transfer_Size: 0.05204 Digital_Transfer_Option: Online_Option: Computer_Contact_Information: Network_Address: Network_Resource_Name: https://www.sciencebase.gov/catalog/file/get/64a31377d34ef77fcb057059 Network_Resource_Name: https://doi.org/10.5066/P9TUTK7J Access_Instructions: Data can be downloaded using the Network_Resource_Name links. The first link is a direct link to download the zipped file of data and metadata. The second link points to a landing page for the data release. Fees: None. Technical_Prerequisites: These data can be viewed with Microsoft Excel, LibreOffice, Apple Numbers, or any text-reading software. Metadata_Reference_Information: Metadata_Date: 20230901 Metadata_Contact: Contact_Information: Contact_Organization_Primary: Contact_Organization: U.S. Geological Survey, Pacific Coastal and Marine Science Center Contact_Person: PCMSC Science Data Coordinator Contact_Address: Address_Type: mailing and physical Address: 2885 Mission Street City: Santa Cruz State_or_Province: CA Postal_Code: 95060 Contact_Voice_Telephone: 831-460-7401 Contact_Electronic_Mail_Address: pcmsc_data@usgs.gov Metadata_Standard_Name: Content Standard for Digital Geospatial Metadata Metadata_Standard_Version: FGDC-STD-001-1998