Numerical modeling

modeling that uses numerical inputs for variables to simulate the behavior of a real-world system; use this term for finite element modeling and computer simulation.
This category is also used for mathematical simulation and numerical simulation.
Subtopics:
(none)

88 results listed by similarity [list alphabetically]
Physics-based numerical model simulations of wave propagation over and around theoretical atoll and island morphologies for sea-level rise scenarios

Schematic atoll models with varying theoretical morphologies were used to evaluate the relative control of individual morphological parameters on alongshore transport gradients. Here we present physics-based numerical SWAN model results of incident wave transformations for a range of atoll and island morphologies and sea-level rise scenarios. Model results are presented in NetCDF format, accompanied by a README text file that lists the parameters used in each model run. These data accompany the following ...

Info
Physics-based numerical circulation model outputs of ocean surface circulation during the 2010-2013 summer coral-spawning seasons in Maui Nui, Hawaii, USA

Ocean surface current results from a physics-based, 3-dimensional coupled ocean-atmosphere numerical model were generated to understand coral larval dispersal patterns in Maui Nui, Hawaii, USA. The model was used to simulate coral larval dispersal patterns from a number of existing State-managed reefs and large tracks of reefs with high coral coverage that might be good candidates for marine-protected areas (MPAs) during 8 spawning events during 2010-2013. The goal of this effort is to provide geophysical ...

Info
Model input and output files for modeling surface gravity waves on a schematized ancient lake on Mars

This portion of the data release presents a wave model application developed to simulate wind generated surface gravity waves on an ancient lake on Mars. The phase-averaged wave model, SWAN, was applied within the Delft3D modeling system (Deltares, 2018) with reduced gravity and a range of atmospheric densities and wind speeds to simulate potential conditions that could generate wind waves on Mars. The data release includes model input files for simulations with three different atmospheric densities, ...

Info
Tabulated wave parameter results from modeling surface gravity waves on a schematized ancient lake on Mars

This portion of the data release presents tabulated wave parameter results derived from simulations of wind generated surface gravity waves on an ancient lake on Mars. The phase-averaged wave model, SWAN, was applied within the Delft3D modeling system (Deltares, 2018) with reduced gravity and a range of atmospheric densities and wind speeds to simulate potential conditions that could generate wind waves on Mars.

Info
Salish Sea water level validation simulations: 2017-2020

Simulations of water levels in the Salish Sea over the period October 1, 2016 to September 30, 2020 were conducted to validate the Salish Sea hydrodynamic model. The model accounts for sea level position, tides, remote sea-level anomalies, local winds and storm surge and stream flows as they affect water density. Comparison of modeled and measured water levels showed the model predicts extreme water levels at NOAA and USGS tide gage stations within 0.15 m. Model inputs and outputs of time-series forcing and ...

Info
Salish Sea water level simulation projections: 2016-2099

Simulations of the period 2016-2099 were conducted using the Salish Sea hydrodynamic model to evaluate extreme water levels associated with anticipated changes in sea level and climate forcing. The model projections accounting for sea level position, tides, remote sea-level anomalies, local winds and storm surge and stream flows as they affect water density. Dynamically downscaled Weather Research and Forecasting (WRF) CMIP5 GFDL wind and atmospheric pressure fields were prescribed over the model open ...

Info
Salish Sea water level hindcast simulations: 1985-2015

Simulatations of water levels in the Salish Sea for a continuous hindcast of the period October 1, 1985, to September 30, 2015 were conducted to evaluate the utility and skill of a sea-level anomaly predictor and to develop extreme water level estimates accounting for decadal climate variability. The model accounts for sea level position, tides, remote sea-level anomalies, local winds and storm surge and stream flows as they affect water density. Comparison of modeled and measured water levels showed the ...

Info
Ocean wave time-series data along the U.S. West Coast and surrounding Hawai’i simulated with a global-scale numerical wave model under the influence of CMIP6 wind and sea ice fields (ver. 2.0, October 2024)

This dataset presents historical (1979-2014) and projected (2020-2050) hourly time-series of wave heights, wave periods, incident wave directions, and directional spreading at distinct points along the U.S. West Coast and surrounding Hawai’i. The time-series were developed by running the National Oceanic and Atmospheric Administration’s (NOAA’s) WAVEWATCHIII model. Wind and sea-ice fields from seven different Global Climate or General Circulation Models from the CMIP6 High-Resolution Model ...

Info
Ocean wave time-series data surrounding Hawai’i and U.S. territories in the Pacific Ocean simulated with a global-scale numerical wave model under the influence of CMIP6 wind and sea ice fields (ver. 2.0, October 2024)

This dataset presents historical (1979-2014) and projected (2020-2050) hourly time-series of wave heights, wave periods, incident wave directions, and directional spreading at distinct points surrounding Hawai’i and U.S. territories in the Pacific Ocean. The time-series were developed by running the National Oceanic and Atmospheric Administration’s (NOAA’s) WAVEWATCHIII model. Wind and sea ice fields from seven different Global Climate or General Circulation Models from the CMIP6 High-Resolution Model ...

Info
Ocean wave time-series data along the Alaska coast simulated with a global-scale numerical wave model under the influence of CMIP6 wind and sea ice fields (ver. 2.0, October 2024)

This dataset presents historical (1979-2014) and projected (2020-2050) hourly time-series of wave heights, wave periods, incident wave directions and directional spreading at distinct points along the open coast of Alaska. The time-series were developed by running the National Oceanic and Atmospheric Administration’s (NOAA’s) WAVEWATCHIII model. Wind and sea ice fields from seven different Global Climate or General Circulation Models from the CMIP6 High-Resolution Model Intercomparison Project were used ...

Info
Ocean wave time-series data along the U.S. Atlantic, Gulf of Mexico, and Puerto Rico coasts simulated with a global-scale numerical wave model under the influence of CMIP6 wind and sea ice fields (ver. 2.0, October 2024)

This dataset presents historical (1979-2014) and projected (2020-2050) hourly time-series of wave heights, wave periods, incident wave directions, and directional spreading at distinct points along the U.S. Atlantic, Gulf of Mexico, and Puerto Rico. The time-series were developed by running the National Oceanic and Atmospheric Administration’s (NOAA’s) WAVEWATCHIII model. Wind and sea ice fields from seven different Global Climate or General Circulation Models from the CMIP6 High-Resolution Model ...

Info
Recurrence interval of sediment mobility at select points in the Gulf of Mexico for May 2010 to May 2011 (GMEX_mobile_freq, Geographic, WGS 84)

The U.S. Geological Survey has been characterizing the regional variation in shear stress on the sea floor and sediment mobility through statistical descriptors. The purpose of this project is to identify patterns in stress in order to inform habitat delineation or decisions for anthropogenic use of the continental shelf. The statistical characterization spans the continental shelf from the coast to approximately 120 m water depth, at approximately 0.04-0.06 degree (5-7 km, depending on latitude) ...

Info
The median of bottom shear stress for the Gulf of Mexico, May 2010 to May 2011 (GMEX_median, Geographic, WGS 84)

The U.S. Geological Survey has been characterizing the regional variation in shear stress on the sea floor and sediment mobility through statistical descriptors. The purpose of this project is to identify patterns in stress in order to inform habitat delineation or decisions for anthropogenic use of the continental shelf. The statistical characterization spans the continental shelf from the coast to approximately 120 m water depth, at approximately 0.04-0.06 degree (5-7 km, depending on latitude) ...

Info
The half-interpercentile range of bottom shear stress for the Gulf of Mexico, May 2010 to May 2011 (GMEX_hIPR, Geographic, WGS 84)

The U.S. Geological Survey has been characterizing the regional variation in shear stress on the sea floor and sediment mobility through statistical descriptors. The purpose of this project is to identify patterns in stress in order to inform habitat delineation or decisions for anthropogenic use of the continental shelf. The statistical characterization spans the continental shelf from the coast to approximately 120 m water depth, at approximately 0.04-0.06 degree (5-7 km, depending on latitude) ...

Info
The 95th percentile of bottom shear stress for the Gulf of Mexico, May 2010 to May 2011 (GMEX_95th_perc, Geographic, WGS 84)

The U.S. Geological Survey has been characterizing the regional variation in shear stress on the sea floor and sediment mobility through statistical descriptors. The purpose of this project is to identify patterns in stress in order to inform habitat delineation or decisions for anthropogenic use of the continental shelf. The statistical characterization spans the continental shelf from the coast to approximately 120 m water depth, at approximately 0.04-0.06 degree (5-7 km, depending on latitude) ...

Info
Percentage of time sediment is mobile for May, 2010 - May, 2011 at select points in the Gulf of Maine south into the Middle Atlantic Bight (GMAINE_mobile_perc.SHP, Geographic, WGS 84)

The U.S. Geological Survey has been characterizing the regional variation in shear stress on the sea floor and sediment mobility through statistical descriptors. The purpose of this project is to identify patterns in stress in order to inform habitat delineation or decisions for anthropogenic use of the continental shelf. The statistical characterization spans the continental shelf from the coast to approximately 120 m water depth, at approximately 0.03 degree (2.5-3.75 km, depending on latitude) ...

Info
Recurrence interval of sediment mobility at select points in the Gulf of Maine south into the Middle Atlantic Bight for May, 2010 - May, 2011 (GMAINE_mobile_freq, Geographic, WGS 84)

The U.S. Geological Survey has been characterizing the regional variation in shear stress on the sea floor and sediment mobility through statistical descriptors. The purpose of this project is to identify patterns in stress in order to inform habitat delineation or decisions for anthropogenic use of the continental shelf. The statistical characterization spans the continental shelf from the coast to approximately 120 m water depth, at approximately 0.03 degree (2.5-3.75 km, depending on latitude) ...

Info
The median of bottom shear stress for the Gulf of Maine south into the Middle Atlantic Bight, May 2010 to May 2011 (GMAINE_median.shp, Geographic, WGS 84)

The U.S. Geological Survey has been characterizing the regional variation in shear stress on the sea floor and sediment mobility through statistical descriptors. The purpose of this project is to identify patterns in stress in order to inform habitat delineation or decisions for anthropogenic use of the continental shelf. The statistical characterization spans the continental shelf from the coast to approximately 120 m water depth, at approximately 0.03 degree (2.5-3.75 km, depending on latitude) ...

Info
The half interpercentile range of bottom shear stress for the Gulf of Maine south into the Middle Atlantic Bight, May 2010 to May 2011 (GMAINE_hIPR, Geographic, WGS 84)

The U.S. Geological Survey has been characterizing the regional variation in shear stress on the sea floor and sediment mobility through statistical descriptors. The purpose of this project is to identify patterns in stress in order to inform habitat delineation or decisions for anthropogenic use of the continental shelf. The statistical characterization spans the continental shelf from the coast to approximately 120 m water depth, at approximately 0.03 degree (2.5-3.75 km, depending on latitude) ...

Info
The 95th percentile of bottom shear stress for the Gulf of Maine south into the Middle Atlantic Bight, May 2010 to May 2011 (GMAINE_95th_perc.shp, Geographic, WGS 84)

The U.S. Geological Survey has been characterizing the regional variation in shear stress on the sea floor and sediment mobility through statistical descriptors. The purpose of this project is to identify patterns in stress in order to inform habitat delineation or decisions for anthropogenic use of the continental shelf. The statistical characterization spans the continental shelf from the coast to approximately 120 m water depth, at approximately 0.03 degree (2.5-3.75 km, depending on latitude) ...

Info
Hydrodynamic and Sediment Transport Model Application for OSAT3 Guidance: Surf-zone integrated alongshore potential flux for oil-sand balls of varying sizes weighted by probability of wave scenario occurrence

The U.S. Geological Survey has developed a method for estimating the mobility and potential alongshore transport of heavier-than-water sand and oil agglomerates (tarballs or surface residual balls, SRBs). During the Deepwater Horizon spill, some oil that reached the surf zone of the northern Gulf of Mexico mixed with suspended sediment and sank to form sub-tidal mats. If not removed, these mats can break apart to form SRBs and subsequently re-oil the beach. A method was developed for estimating SRB ...

Info
Hydrodynamic and Sediment Transport Model Application for OSAT3 Guidance: Ratio of the wave- and current-induced shear stress to the critical value for oil-tar balls and sediment mobilization weighted by probability of wave scenario occurrence

The U.S. Geological Survey has developed a method for estimating the mobility and potential alongshore transport of heavier-than-water sand and oil agglomerates (tarballs or surface residual balls, SRBs). During the Deepwater Horizon spill, some oil that reached the surf zone of the northern Gulf of Mexico mixed with suspended sediment and sank to form sub-tidal mats. If not removed, these mats can break apart to form SRBs and subsequently re-oil the beach. A method was developed for estimating SRB ...

Info
Hydrodynamic and Sediment Transport Model Application for OSAT3 Guidance: Ratio of the wave- and current-induced shear stress to the critical value for oil-tar balls and sediment mobilization over a tidal cycle

The U.S. Geological Survey has developed a method for estimating the mobility and potential alongshore transport of heavier-than-water sand and oil agglomerates (tarballs or surface residual balls, SRBs). During the Deepwater Horizon spill, some oil that reached the surf zone of the northern Gulf of Mexico mixed with suspended sediment and sank to form sub-tidal mats. If not removed, these mats can break apart to form SRBs and subsequently re-oil the beach. A method was developed for estimating SRB ...

Info
Tidal_Grid

The U.S. Geological Survey has developed a method for estimating the mobility and potential alongshore transport of heavier-than-water sand and oil agglomerates (tarballs or surface residual balls, SRBs). During the Deepwater Horizon spill, some oil that reached the surf zone of the northern Gulf of Mexico mixed with suspended sediment and sank to form sub-tidal mats. If not removed, these mats can break apart to form SRBs and subsequently re-oil the beach. A method was developed for estimating SRB ...

Info
Scenarios_Grid

The U.S. Geological Survey has developed a method for estimating the mobility and potential alongshore transport of heavier-than-water sand and oil agglomerates (tarballs or surface residual balls, SRBs). During the Deepwater Horizon spill, some oil that reached the surf zone of the northern Gulf of Mexico mixed with suspended sediment and sank to form sub-tidal mats. If not removed, these mats can break apart to form SRBs and subsequently re-oil the beach. A method was developed for estimating SRB ...

Info
Hydrodynamic and Sediment Transport Model Application for OSAT3 Guidance: peak wave period

The U.S. Geological Survey has developed a method for estimating the mobility and potential alongshore transport of heavier-than-water sand and oil agglomerates (tarballs or surface residual balls, SRBs). During the Deepwater Horizon spill, some oil that reached the surf zone of the northern Gulf of Mexico mixed with suspended sediment and sank to form sub-tidal mats. If not removed, these mats can break apart to form SRBs and subsequently re-oil the beach. A method was developed for estimating SRB ...

Info
Hydrodynamic and Sediment Transport Model Application for OSAT3 Guidance: Significant wave height

The U.S. Geological Survey has developed a method for estimating the mobility and potential alongshore transport of heavier-than-water sand and oil agglomerates (tarballs or surface residual balls, SRBs). During the Deepwater Horizon spill, some oil that reached the surf zone of the northern Gulf of Mexico mixed with suspended sediment and sank to form sub-tidal mats. If not removed, these mats can break apart to form SRBs and subsequently re-oil the beach. A method was developed for estimating SRB ...

Info
Hydrodynamic and Sediment Transport Model Application for OSAT3 Guidance: wave direction

The U.S. Geological Survey has developed a method for estimating the mobility and potential alongshore transport of heavier-than-water sand and oil agglomerates (tarballs or surface residual balls, SRBs). During the Deepwater Horizon spill, some oil that reached the surf zone of the northern Gulf of Mexico mixed with suspended sediment and sank to form sub-tidal mats. If not removed, these mats can break apart to form SRBs and subsequently re-oil the beach. A method was developed for estimating SRB ...

Info
Hydrodynamic and Sediment Transport Model Application for OSAT3 Guidance: Surf-zone integrated alongshore potential flux for oil-sand balls

The U.S. Geological Survey has developed a method for estimating the mobility and potential alongshore transport of heavier-than-water sand and oil agglomerates (tarballs or surface residual balls, SRBs). During the Deepwater Horizon spill, some oil that reached the surf zone of the northern Gulf of Mexico mixed with suspended sediment and sank to form sub-tidal mats. If not removed, these mats can break apart to form SRBs and subsequently re-oil the beach. A method was developed for estimating SRB ...

Info
Hydrodynamic and Sediment Transport Model Application for OSAT3 Guidance: Ratio of wave- and current-induced shear stress to critical values for oil-sand ball and sediment mobilization

The U.S. Geological Survey has developed a method for estimating the mobility and potential alongshore transport of heavier-than-water sand and oil agglomerates (tarballs or surface residual balls, SRBs). During the Deepwater Horizon spill, some oil that reached the surf zone of the northern Gulf of Mexico mixed with suspended sediment and sank to form sub-tidal mats. If not removed, these mats can break apart to form SRBs and subsequently re-oil the beach. A method was developed for estimating SRB ...

Info
Hydrodynamic and Sediment Transport Model Application for OSAT3 Guidance: Locations of decelerations in the direction of flow in the maximum alongshore current

The U.S. Geological Survey has developed a method for estimating the mobility and potential alongshore transport of heavier-than-water sand and oil agglomerates (tarballs or surface residual balls, SRBs). During the Deepwater Horizon spill, some oil that reached the surf zone of the northern Gulf of Mexico mixed with suspended sediment and sank to form sub-tidal mats. If not removed, these mats can break apart to form SRBs and subsequently re-oil the beach. A method was developed for estimating SRB ...

Info
Hydrodynamic and Sediment Transport Model Application for OSAT3 Guidance: Locations of convergences in the maximum alongshore current

The U.S. Geological Survey has developed a method for estimating the mobility and potential alongshore transport of heavier-than-water sand and oil agglomerates (tarballs or surface residual balls, SRBs). During the Deepwater Horizon spill, some oil that reached the surf zone of the northern Gulf of Mexico mixed with suspended sediment and sank to form sub-tidal mats. If not removed, these mats can break apart to form SRBs and subsequently re-oil the beach. A method was developed for estimating SRB ...

Info
Model parameter input files to study three-dimensional flow over coral reef spur-and-groove morphology

This data set consists of physics-based Delft3D-FLOW and SWAN hydrodynamic models input files used to study the wave-induced 3D flow over spur-and-groove (SAG) formations. SAG are a common and impressive characteristic of coral reefs. They are composed of a series of submerged shore-normal coral ridges (spurs) separated by shore-normal patches of sediment (grooves) on the fore reef of coral reef environments. Although their existence and geometrical properties are well documented, the literature concerning ...

Info
Model parameter input files to compare wave-averaged versus wave-resolving XBeach coastal flooding models for coral reef-lined coasts

This data release includes the XBeach input data files used to evaluate the importance of explicitly modeling sea-swell waves for runup. This was examined using a 2D XBeach short wave-averaged (surfbeat, XB-SB) and a wave-resolving (non-hydrostatic, XB-NH) model of Roi-Namur Island on Kwajalein Atoll in the Republic of Marshall Islands. Results show that explicitly modelling the sea-swell component (using XB-NH) provides a better approximation of the observed runup than XB-SB (which only models the time ...

Info
Hydrodynamic model of the San Francisco Bay and Delta, California

A one- and two-dimensional hydrodynamic model of the San Francisco Bay and Delta was constructed using the Delft3D Flexible Mesh Suite (Delft3D FM; Kernkamp and others, 2011; https://www.deltares.nl/en/software/delft3d-flexible-mesh-suite/) to simulate still water levels. Required model input files are provided to run the model for the time period from October 1, 2018, to April 30, 2019. This data release describes the construction and validation of the model application and provides input files suitable to ...

Info
Modeled effects of depth and semidiurnal temperature fluctuations on predictions of year that coral reef locations reach annual severe bleaching for various global climate model projections

Using global climate model projections of sea-surface temperature at coral reef sites, we modeled the effects of depth and exposure to semidiurnal temperature fluctuations to examine how these effects may alter the projected year of annual severe bleaching for coral reef sites globally. Here we present the first global maps of the effects these processes have on bleaching projections for three IPCC-AR5 emissions scenarios.

Info
Hindcast (1981-2010) and projected (2011-2100) coastal storm events, including duration, wave conditions, and storm surges in the vicinity of Arey Lagoon and Barter Island, Alaska

Numerically modeled ocean storm conditions of hindcast (1981-2010) and projected (2011-2100) storm events in the nearshore region of Arey Lagoon, Alaska. Storms were identified from time-series of dynamically downscaled deep-water wave conditions using WaveWatch3 (WW3) and nearshore storm surges using the Deltares Delft3D model. A storm was defined as having offshore water wave heights >= 2 meters (m) and storm surges >=0 m. The data in this file provide a listing of individual storm dates, storm duration, ...

Info
Projected open water seasons using four global climate models for 2011 to 2100 fronting Arey Lagoon and Barter Island, Alaska

Estimated start date, end date, and duration of open water at a location fronting Barter Island, Alaska derived from projected sea ice extents in 4 global climate models: MIROC5, BCC-CSM1.1, INM-CM4, and GFDL-ESM2M. Starting and ending dates are when sea ice retreated or is projected to retreat offshore by more than 80 kilometers fronting Barter Island. Projected coastal storm events were derived by downscaling atmospheric conditions of the RCP 4.5 climate scenario with the MIROC5 global climate model (GCM) ...

Info
Seamless topo-bathy digital elevation model (DEM) of Arey Lagoon, Alaska

A seamless topographic-bathymetric digital elevation model for an area around Arey Lagoon, Alaska created from a combination of lidar elevation data collected in 2009, single-beam bathymetric data collected in 2011, and NOS sounding data collected in 1948.

Info
Wave time-series data collected in 2011 in the vicinity of Arey Lagoon and Barter Island, Alaska

Time-series measurements of waves, currents, water levels, sea surface temperatures, ocean salinity, and water, air, and ground temperatures were collected in July through September 2011 in and around Arey Lagoon, near Barter Island, Alaska. Directional wave spectra, currents, water levels, salinity, and bottom and surface water temperatures were measured with a bottom-mounted 1MHz Nortek AWAC, HOBO temperature loggers, and a Solinst Levelogger in ~5m water depth offshore of Arey Island. Within Arey Lagoon, ...

Info
Sea-surface water temperature time-series data collected in 2011 in the vicinity of Arey Lagoon and Barter Island, Alaska

Time-series measurements of waves, currents, water levels, sea surface temperatures, ocean salinity, and water, air, and ground temperatures were collected in July through September 2011 in and around Arey Lagoon, near Barter Island, Alaska. Directional wave spectra, currents, water levels, salinity, and bottom and surface water temperatures were measured with a bottom-mounted 1MHz Nortek AWAC, HOBO temperature loggers, and a Solinst Levelogger in ~5m water depth offshore of Arey Island. Within Arey Lagoon, ...

Info
Ground temperature time-series data collected in 2011 in the vicinity of Arey Lagoon and Barter Island, Alaska

Time-series measurements of waves, currents, water levels, sea surface temperatures, ocean salinity, and water, air, and ground temperatures were collected in July through September 2011 in and around Arey Lagoon, near Barter Island, Alaska. Directional wave spectra, currents, water levels, salinity, and bottom and surface water temperatures were measured with a bottom-mounted 1MHz Nortek AWAC, HOBO temperature loggers, and a Solinst Levelogger in ~5m water depth offshore of Arey Island. Within Arey Lagoon, ...

Info
Current-velocity time-series data collected in 2011 in the vicinity of Arey Lagoon and Barter Island, Alaska

Time-series measurements of waves, currents, water levels, sea surface temperatures, ocean salinity, and water, air, and ground temperatures were collected in July through September 2011 in and around Arey Lagoon, near Barter Island, Alaska. Directional wave spectra, currents, water levels, salinity, and bottom and surface water temperatures were measured with a bottom-mounted 1MHz Nortek AWAC, HOBO temperature loggers, and a Solinst Levelogger in ~5m water depth offshore of Arey Island. Within Arey Lagoon, ...

Info
Conductivity, temperature and depth time-series data collected in 2011 in the vicinity of Arey Lagoon and Barter Island, Alaska

Time-series measurements of waves, currents, water levels, sea surface temperatures, ocean salinity, and water, air, and ground temperatures were collected in July through September 2011 in and around Arey Lagoon, near Barter Island, Alaska. Directional wave spectra, currents, water levels, salinity, and bottom and surface water temperatures were measured with a bottom-mounted 1MHz Nortek AWAC, HOBO temperature loggers, and a Solinst Levelogger in ~5m water depth offshore of Arey Island. Within Arey Lagoon, ...

Info
Thermokarst lake water temperature and salinity data collected in 2011 in the vicinity of Arey Lagoon and Barter Island, Alaska

Thermokarst lake water temperature and salinity data were collected in 2011 in the vicinity of Arey Lagoon and Barter Island, Alaska. Pond temperatures and salinity (conductivity) were measured along two transects traversing across a wet sedge area. A hand-held YSI 556 MPS (plus or minus 0.5 percent accuracy) with a cable-attached instrument probe was placed in 10-15 cm of water within 1 m of each of the pond edges and allowed to equilibrate, and readings were recorded manually. In all, 35 ponds were ...

Info
Mean grain size of beach and seabed sediment samples collected in the vicinity of Arey Lagoon and Barter Island, Alaska, July 2011

Sediment grab samples were collected on the barriers and nearby seabed on and around Arey and Barter Islands, Alaska in July 2011 and analyzed for mean grain size. 43 terrestrial grab samples were collected along 14 shore-normal beach transects (12 on Arey Island and 2 on the western spit of Barter Island) at the seaward water line, the berm crest or top of the island, and at the lagoon water line. 11 seabed samples were collected using a small pipe dredge deployed from a small boat; 2 in the vicinity of ...

Info
Beach profile data collected in 2010 and 2011 in the vicinity of Arey Lagoon and Barter Island, Alaska

Beach elevation profiles were measured along 29 shore-normal transects on and around Arey and Barter Islands, Alaska in August 2010 and July 2011. Profile data are available in a single comma-delimited file and a zip file including multiple .jpg images that show a visual representation of the individual profiles.

Info
Single-beam bathymetry data collected in 2010 and 2011 in the vicinity of Arey Lagoon and Barter Islands, Alaska

Single-beam bathymetry data were collected in 2010 and 2011 in the nearshore waters around Barter Island, Arey Island, and within Arey Lagoon, Alaska. Measurements were made from a small boat or dinghy using one of three systems: a Humminbird 898 SI Fish Finder with integrated GPS (2010 and 2011), an Ohmex Sonarmite BT integrated with a Trimble GeoHX series GPS (2011), or a Garmin Sounder with integrated GPS (2011). Each system collected single-beam water depth with accuracies better than 4 meters (m) ...

Info
Hydrodynamic and sediment transport model of San Francisco Bay, California, Nov-Dec 2014

A three-dimensional hydrodynamic and sediment transport model of San Pablo and Suisun Bays was constructed using the Delft3D4 (D3D) modeling suite (Deltares, 2021a) to simulate water levels, flow, waves, and suspended sediment for time period of Nov 1 to Dec 31, 2014. This data release describes the construction and validation of the model application and provides input files suitable to run the model on D3D software version 4.04.01.

Info
Hydrodynamic model of the lower Columbia River, Oregon and Washington, 2017-2020

A three-dimensional hydrodynamic model of the lower Columbia River (LCR) was constructed using the Delft3D Flexible Mesh (DFM) modeling suite to simulate water levels, flow, and seabed stresses for time period of January 1, 2017 to April 20, 2020. This data release describes the construction and validation of the model application and provides input files suitable to run the model on Delft3D Flexible Mesh software version 2021.01.

Info
Coral reef profiles for wave-runup prediction

This data release includes representative cluster profiles (RCPs) from a large (>24,000) selection of coral reef topobathymetric cross-shore profiles (Scott and others, 2020). We used statistics, machine learning, and numerical modelling to develop the set of RCPs, which can be used to accurately represent the shoreline hydrodynamics of a large variety of coral reef-lined coasts around the globe. In two stages, the data were reduced by clustering cross-shore profiles based on morphology and hydrodynamic ...

Info
Model parameter input files to compare the influence of channels in fringing coral reefs on alongshore variations in wave-driven runup along the shoreline

An extensive set of physics-based XBeach Non-hydrostatic hydrodynamic model simulations (with input files here included) were used to evaluate the influence of shore-normal reef channels on flooding along fringing reef-lined coasts, specifically during extreme wave conditions when the risk for coastal flooding and the resulting impact to coastal communities is greatest. These input files accompany the modeling conducted for the following publication: Storlazzi, C.D., Rey, A.E., and van Dongeren, A.R., 2022, ...

Info
Projected flood water depths on Roi-Namur, Kwajalein Atoll, Republic of the Marshall Islands

Projected future wave-driven flooding depths on Roi-Namur Island on Kwajalein Atoll in the Republic of the Marshall Islands for a range of climate-change scenarios. This study utilized field data to calibrate oceanographic and hydrogeologic models, which were then used with climate-change and sea-level rise projections to explore the effects of sea-level rise and wave-driven flooding on atoll islands and their freshwater resources. The overall objective of this effort, due to the large uncertainty in ...

Info
BEWARE database: A Bayesian-based system to assess wave-driven flooding hazards on coral reef-lined coasts

A process-based wave-resolving hydrodynamic model (XBeach Non-Hydrostatic, ‘XBNH’) was used to create a large synthetic database for use in a “Bayesian Estimator for Wave Attack in Reef Environments” (BEWARE), relating incident hydrodynamics and coral reef geomorphology to coastal flooding hazards on reef-lined coasts. Building on previous work, BEWARE improves system understanding of reef hydrodynamics by examining the intrinsic reef and extrinsic forcing factors controlling runup and flooding on ...

Info
Model parameter input files to compare locations of coral reef restoration on different reef profiles to reduce coastal flooding

This dataset consists of physics-based XBeach Non-hydrostatic hydrodynamic models input files used to study how coral reef restoration affects waves and wave-driven water levels over coral reefs, and the resulting wave-driven runup on the adjacent shoreline. Coral reefs are effective natural coastal flood barriers that protect adjacent communities. Coral degradation compromises the coastal protection value of reefs while also reducing their other ecosystem services, making them a target for restoration. ...

Info
HyCReWW database: A hybrid coral reef wave and water level metamodel

We developed the HyCReWW metamodel to predict wave run-up under a wide range of coral reef morphometric and offshore forcing characteristics. Due to the complexity and high dimensionality of the problem, we assumed an idealized one-dimensional reef profile, characterized by seven primary parameters. XBeach Non-Hydrostatic was chosen to create the synthetic dataset and Radial Basis Functions implemented in Matlab were chosen for interpolation. Results demonstrate the applicability of the metamodel to obtain ...

Info
Nearshore waves in southern California: hindcast, and modeled historical and 21st-century projected time series

Abstract: This data release presents modeled time series of nearshore waves along the southern California coast, from Point Conception to the Mexican border, hindcasted for 1980-2010 and projected using global climate model forcing for 1975-2005 and 2012-2100. Details: As part of the Coastal Storm Modeling System (CoSMoS), time series of hindcast, historical, and 21st-century nearshore wave parameters (wave height, period, and direction) were simulated for the southern California coast from Point Conception ...

Info
Dynamically downscaled future wave projections from SWAN model results for the main Hawaiian Islands

Projected wave climate trends from WAVEWATCH3 model output were used as input for nearshore wave models (for example, SWAN) for the main Hawaiian Islands to derive data and statistical measures (mean and top 5 percent values) of wave height, wave period, and wave direction for the recent past (1996-2005) and future projections (2026-2045 and 2085-2100). Three-hourly global climate model (GCM) wind speed and wind direction output from four different GCMs provided by the Coupled Model Inter-Comparison Project ...

Info
BEWARE2 database: A meta-process model to assess wave-driven flooding hazards on morphologically diverse, coral reef-lined coasts

This dataset contains the reef profiles and resulting hydrodynamic outputs of the "Broad-range Estimator of Wave Attack in Reef Environments" (BEWARE-2) meta-process modeling system. A process-based, wave-resolving hydrodynamic model (XBeach Non-Hydrostatic+, "XBNH+") was used to create a large synthetic database for use in BEWARE-2, relating incident hydrodynamics and coral reef geomorphology to coastal flooding hazards on reef-lined coasts. Building on previous work, BEWARE-2 improves system understanding ...

Info
Modeled nearshore wave parameters

This portion of the USGS data release contains simulated nearshore wave parameters derived from a stand-alone spectral wave model of the Columbia River littoral cell, Washington and Oregon. The model output includes significant wave heights, peak wave periods, mean wave directions, and water depths for a series of 221 shore normal transects that extended from the coastline to the -15 m NAVD88 elevation (about 16.5 m average water depth). Data are provided at the seaward extent of each transect as well as at ...

Info
Spectral wave model input files

A stand-alone wave model application was constructed using the spectral wave model SWAN within the Delft3D4 (version 4.04.01) modeling system to simulate nearshore wave dynamics along the coast of the Columbia River littoral cell, Washington and Oregon. Nearshore wave dynamics are solved at hourly intervals on a series of nested grids with resolutions varying between 750 m for the largest grid to about 80 m for the two detailed grids that cover the Grays Harbor and Columbia River inlets. The provided model ...

Info
Wave time-series: ERA5 hindcast period 1979-2019 - U.S. Canada border to Bering Strait

Modeled wave time series data are presented for the hindcast period of 1979 to 2019 from the U.S. Canada border to the Bering Strait close to the 5 and 10 m isobaths. Outputs include three-hourly nearshore significant wave heights (Hs), mean wave periods (Tm) and mean wave directions (Dm) for 6424 locations. Data are available as netCDF files and are packaged for the Beaufort Sea region from the U.S. Canada border to Nuvuk (Point Barrow), and for the Chukchi Sea region from Nuvuk to Kotzebue Sound and from ...

Info
Wave model input files

Provided here are the required input files to run a standalone wave model (Simulating Waves WAves Nearshore [SWAN]; Booij and others, 1999) on eleven model domains from the Canada-U.S. border to Norton Sound, Alaska to create a downscaled wave database (DWDB). The DWDB, in turn, can be used to reconstruct hindcast (1979-2019) and projected (2020-2050) time series at each point in the model domains see Engelstad and others, 2023 for further information on reconstruction of time-series. The model forcing ...

Info
Time series for the central Beaufort Sea coast, Alaska

Time series output from a spectral wave model (Simulating Waves WAves Nearshore [SWAN]; Booij and others 1999), implemented for the central Beaufort Sea coast of Alaska from 1979 to 2019, are provided. The variables include significant wave heights, mean wave periods, mean wave directions, wave steepness, and orbital velocities. Additionally, water depths, x (east-west) and y (north-south) components of the wind, and sea ice concentrations are provided. Further information can be found in Nederhoff and ...

Info
Nearshore parametric wave setup hindcast data (1979-2019) for the North and South Carolina coasts

This dataset presents alongshore wave setup timeseries for the North and South Carolina coastlines. Wave setup was modelled using parameterization for open coast sandy beaches as presented in Stockdon and others (2006). The parameterization relates onshore wave setup to offshore wave conditions and beach characteristics. Wave conditions were extracted at approximately the 10 m depth contour and reverse shoaled to the deep-water condition. These data were then matched to cross-shore transects spaced at ...

Info
Nearshore parametric wave setup future projections (2020-2050) for the North and South Carolina coasts

This dataset presents alongshore wave setup timeseries for the North and South Carolina coastlines. Wave setup was modelled using parameterization for open coast sandy beaches as presented in Stockdon and others (2006). The parameterization relates onshore wave setup to offshore wave conditions and beach characteristics. Wave conditions were extracted at approximately the 10 m depth contour and reverse shoaled to the deep-water condition. These data were then matched to cross-shore transects spaced at ...

Info
Nearshore water level, tide, and non-tidal residual hindcasts (1979-2016) for the North and South Carolina coasts

A dataset of modeled nearshore water levels (WLs) was developed for the North and South Carolina coastlines. Water levels, defined for this dataset as the linear sum of tides and non-tidal residuals (NTR), were produced by Muis and others (2016) using a global tide and surge model (GTSM) forced by global atmospheric fields -. Water level outputs were extracted from the global grid at approximately 20 km resolution along the coastlines. These data were then statistically downscaled using a signal-specific ...

Info
Nearshore water level, tide, and non-tidal residual future projections (2016-2050) for the North and South Carolina coasts

A dataset of modeled nearshore water levels (WLs) was developed for the North and South Carolina coastlines. Water levels, defined for this dataset as the linear sum of tides and non-tidal residuals (NTR), were produced by Muis and others (2016) using a global tide and surge model (GTSM) forced by global atmospheric fields. Water level outputs were extracted from the global grid at approximately 20 km resolution along the southeast Atlantic coastline. These data were then statistically downscaled using a ...

Info
Nearshore parametric wave setup hindcast data (1979-2019) for the U.S. Atlantic coast

This dataset presents alongshore wave setup timeseries for three states (Virginia, Georgia, and Florida) along the U.S. Atlantic coast. Wave setup was modelled using parameterization for open coast sandy beaches as presented in Stockdon and others (2006). The parameterization relates onshore wave setup to offshore wave conditions and beach characteristics. Wave conditions were extracted at approximately the 10 m depth contour and reverse shoaled to the deep-water condition. These data were then matched to ...

Info
Nearshore parametric wave setup future projections (2020-2050) for the U.S. Atlantic coast

This dataset presents alongshore wave setup timeseries for three states (Virginia, Georgia, and Florida) along the U.S. Atlantic coast. Wave setup was modelled using parameterization for open coast sandy beaches as presented in Stockdon and others (2006). The parameterization relates onshore wave setup to offshore wave conditions and beach characteristics. Wave conditions were extracted at approximately the 10 m depth contour and reverse shoaled to the deep-water condition. These data were then matched to ...

Info
Nearshore water level, tide, and non-tidal residual hindcasts (1979-2016) for the U.S. Atlantic coast

A dataset of modeled nearshore water levels (WLs) was developed for three states (Virginia, Georgia, and Florida) along the U.S. Atlantic coast. Water levels, defined for this dataset as the linear sum of tides and non-tidal residuals (NTR), were produced by Muis and others (2016) using a global tide and surge model (GTSM) forced by global atmospheric fields -. Water level outputs were extracted from the global grid at approximately 20 km resolution along the coastlines. These data were then statistically ...

Info
Nearshore water level, tide, and non-tidal residual future projections (2016-2050) for the U.S. Atlantic coast

A dataset of modeled nearshore water levels (WLs) was developed for three states (Virginia, Georgia, and Florida) along the U.S. Atlantic coast. Water levels, defined for this dataset as the linear sum of tides and non-tidal residuals (NTR), were produced by Muis and others (2016) using a global tide and surge model (GTSM) forced by global atmospheric fields. Water level outputs were extracted from the global grid at approximately 20 km resolution along the Atlantic coastline. These data were then ...

Info
Model parameter input files to compare the influence of coral reef carbonate budgets on alongshore variations in wave-driven total water levels on Buck Island Reef National Monument

A set of physics-based XBeach Non-hydrostatic hydrodynamic model simulations (with input files here included) were used to evaluate how varying carbonate budgets, and thus coral reef accretion and degradation, affect alongshore variations in wave-driven water levels along the adjacent shoreline of Buck Island Reef National Monument (BUIS) for a number of sea-level rise scenarios, specifically during extreme wave conditions when the risk for coastal flooding and the resulting impact to coastal communities is ...

Info
Model parameter input files to compare effects of stream discharge scenarios on sediment deposition and concentrations around coral reefs off west Maui, Hawaii

This dataset consists of physics-based Delft3D model and Delwaq model input files used in modeling sediment deposition and concentrations around the coral reefs of west Maui, Hawaii. The Delft3D models were used to simulate waves and currents under small (SC1) and large (‘SC2’) wave conditions for current stream discharge (‘Alt1’) and stream discharge with watershed restoration (‘Alt3’). Delft3D model results were subsequently used as forcing conditions for Delwaq models to simulate sediment ...

Info
Hydrodynamic and sediment transport model of the mouth of the Columbia River, Washington and Oregon, 2020-2021

A three-dimensional hydrodynamic and sediment transport model application of the mouth of the Columbia River (MCR) was constructed using the Delft3D4 (D3D) modeling suite (Deltares, 2021) to simulate water levels, flow, waves, and sediment transport for time period of September 22, 2020, to March 10, 2021. The model was used to predict the dispersal of sediment from a submerged, nearshore berm composed of sediment that was dredged from the entrance to the MCR navigation channel and placed on the northern ...

Info
Summary statistics for the central Beaufort Sea coast, Alaska

A nested spectral wave model (Simulating Waves WAves Nearshore [SWAN]; Booij and others, 1999) was deployed for the central Beaufort Sea coast of Alaska to simulate waves for the period from 1979 to 2019. Results in the form of spatial summary statistics, describing wave parameters, wind speed and sea-ice area cover for the intermediate grid (see Overview Image on main page of data release), are provided. Further information can be found in Nederhoff and others (2021).

Info
U.S. Geological Survey calculated percentage of time sediment is mobile for May 2010 to May 2011 at select points in the South Atlantic Bight (SAB_mobile_perc, point shapefile, Geographic, WGS84)

The U.S. Geological Survey has been characterizing the regional variation in shear stress on the sea floor and sediment mobility through statistical descriptors. The purpose of this project is to identify patterns in stress in order to inform habitat delineation or decisions for anthropogenic use of the continental shelf. The statistical characterization spans the continental shelf from the coast to approximately 120 m water depth, at approximately 5 km resolution. Time-series of wave and circulation are ...

Info
Wave model grids and bathymetry for the central Beaufort Sea coast, Alaska

The required grid and bathymetry files to run a nested spectral wave model (Simulating Waves WAves Nearshore [SWAN]; Booij and others, 1999) for the central Beaufort Sea coast of Alaska are provided. A three-level SWAN nesting grid with grid resolutions of 5000 meters, 1000 meters, and 200 meters for the overall, intermediate and detail grids, respectively (see included Browse Graphic) has been developed. For this purpose, available local bathymetry (Coastal Frontiers Corporation, 2014; Kasper and others, ...

Info
U.S. Geological Survey calculated recurrence interval of sediment mobility at select points in the South Atlantic Bight for May 2010 to May 2011 (SAB_mobile_freq, Geographic, WGS 84)

The U.S. Geological Survey has been characterizing the regional variation in shear stress on the sea floor and sediment mobility through statistical descriptors. The purpose of this project is to identify patterns in stress in order to inform habitat delineation or decisions for anthropogenic use of the continental shelf. The statistical characterization spans the continental shelf from the coast to approximately 120 m water depth, at approximately 5 km resolution. Time-series of wave and circulation are ...

Info
U.S. Geological Survey calculated median of wave-current bottom shear stress in the South Atlantic Bight from May 2010 to May 2011 (SAB_median, polygon shapefile, Geographic, WGS84)

The U.S. Geological Survey has been characterizing the regional variation in shear stress on the sea floor and sediment mobility through statistical descriptors. The purpose of this project is to identify patterns in stress in order to inform habitat delineation or decisions for anthropogenic use of the continental shelf. The statistical characterization spans the continental shelf from the coast to approximately 120 m water depth, at approximately 5 km resolution. Time-series of wave and circulation are ...

Info
U.S. Geological Survey calculated half interpercentile range (half of the difference between the 16th and 84th percentiles) of wave-current bottom shear stress in the South Atlantic Bight from May 2010 to May 2011 (SAB_hIPR.shp, polygon shapefile, Geographic, WGS84)

The U.S. Geological Survey has been characterizing the regional variation in shear stress on the sea floor and sediment mobility through statistical descriptors. The purpose of this project is to identify patterns in stress in order to inform habitat delineation or decisions for anthropogenic use of the continental shelf. The statistical characterization spans the continental shelf from the coast to approximately 120 m water depth, at approximately 5 km resolution. Time-series of wave and circulation are ...

Info
U.S. Geological Survey calculated 95th percentile of wave-current bottom shear stress for the South Atlantic Bight for May 2010 to May 2011 (SAB_95th_perc, polygon shapefile, Geographic, WGS84)

The U.S. Geological Survey has been characterizing the regional variation in shear stress on the sea floor and sediment mobility through statistical descriptors. The purpose of this project is to identify patterns in stress in order to inform habitat delineation or decisions for anthropogenic use of the continental shelf. The statistical characterization spans the continental shelf from the coast to approximately 120 m water depth, at approximately 5 km resolution. Time-series of wave and circulation are ...

Info
Percentage of time sediment is mobile for May, 2010 - May, 2011 at select points in the Middle Atlantic Bight (MAB_mobile_perc.SHP)

The U.S. Geological Survey has been characterizing the regional variation in shear stress on the sea floor and sediment mobility through statistical descriptors. The purpose of this project is to identify patterns in stress in order to inform habitat delineation or decisions for anthropogenic use of the continental shelf. The statistical characterization spans the continental shelf from the coast to approximately 120 m water depth, at approximately 5 km resolution. Time-series of wave and circulation are ...

Info
Recurrence interval of sediment mobility at select points in the Middle Atlantic Bight for May, 2010 - May, 2011 (MAB_mobile_freq_v1_1.SHP, Geographic, WGS 84)

The U.S. Geological Survey has been characterizing the regional variation in shear stress on the sea floor and sediment mobility through statistical descriptors. The purpose of this project is to identify patterns in stress in order to inform habitat delineation or decisions for anthropogenic use of the continental shelf. The statistical characterization spans the continental shelf from the coast to approximately 120 m water depth, at approximately 5 km resolution. Time-series of wave and circulation are ...

Info
Median of wave-current bottom shear stress in the Middle Atlantic Bight for May, 2010 - May, 2011 (MAB_median.SHP)

The U.S. Geological Survey has been characterizing the regional variation in shear stress on the sea floor and sediment mobility through statistical descriptors. The purpose of this project is to identify patterns in stress in order to inform habitat delineation or decisions for anthropogenic use of the continental shelf. The statistical characterization spans the continental shelf from the coast to approximately 120 m water depth, at approximately 5 km resolution. Time-series of wave and circulation are ...

Info
Half interpercentile range (half of the difference between the 16th and 84th percentiles) of wave-current bottom shear stress in the Middle Atlantic Bight for May, 2010 - May, 2011 (MAB_hIPR.SHP)

The U.S. Geological Survey has been characterizing the regional variation in shear stress on the sea floor and sediment mobility through statistical descriptors. The purpose of this project is to identify patterns in stress in order to inform habitat delineation or decisions for anthropogenic use of the continental shelf. The statistical characterization spans the continental shelf from the coast to approximately 120 m water depth, at approximately 5 km resolution. Time-series of wave and circulation are ...

Info
95th percentile of wave-current bottom shear stress in the Middle Atlantic Bight for May, 2010 - May, 2011 (MAB_95th_perc.SHP)

The U.S. Geological Survey has been characterizing the regional variation in shear stress on the sea floor and sediment mobility through statistical descriptors. The purpose of this project is to identify patterns in stress in order to inform habitat delineation or decisions for anthropogenic use of the continental shelf. The statistical characterization spans the continental shelf from the coast to approximately 120 m water depth, at approximately 5 km resolution. Time-series of wave and circulation are ...

Info
Percentage of time sediment is mobile for May 2010 to May 2011 at select points in the Gulf of Mexico (GMEX_mobile_perc, Geographic, WGS 84)

The U.S. Geological Survey has been characterizing the regional variation in shear stress on the sea floor and sediment mobility through statistical descriptors. The purpose of this project is to identify patterns in stress in order to inform habitat delineation or decisions for anthropogenic use of the continental shelf. The statistical characterization spans the continental shelf from the coast to approximately 120 m water depth, at approximately 0.04-0.06 degree (5-7 km, depending on latitude) ...

Info