Uncertainty table for lidar-derived shorelines used when calculating rates in the Digital Shoreline Analysis System software for the South Shore of MA

Metadata also available as - [Outline] - [Parseable text] - [XML]

Frequently anticipated questions:


What does this data set describe?

Title:
Uncertainty table for lidar-derived shorelines used when calculating rates in the Digital Shoreline Analysis System software for the South Shore of MA
Abstract:
The Massachusetts Office of Coastal Zone Management launched the Shoreline Change Project in 1989 to identify erosion-prone areas of the coast. The shoreline position and change rate are used to inform management decisions regarding the erosion of coastal resources. In 2001, a 1994 shoreline was added to calculate both long- and short-term shoreline change rates at 40-meter intervals along ocean-facing sections of the Massachusetts coast. In 2013 two oceanfront shorelines for Massachusetts were added using 2008-2009 color aerial orthoimagery and 2007 topographic lidar datasets obtained from NOAA's Ocean Service, Coastal Services Center.
This 2018 update includes two new mean high water (MHW) shorelines for the Massachusetts coast extracted from lidar data collected between 2010-2014. The first new shoreline for the state includes data from 2010 along the North Shore and South Coast from lidar data collected by the U.S. Army Corps of Engineers (USACE) Joint Airborne Lidar Bathymetry Technical Center of Expertise (JALBTCX). Shorelines along the South Shore and Outer Cape are from 2011 lidar data collected by the U.S. Geological Survey's (USGS) National Geospatial Program Office. Shorelines along Nantucket and Martha’s Vineyard are from a 2012 U.S. Army Corps of Engineers Post Sandy Topographic lidar survey. The second new shoreline for the North Shore, Boston, South Shore, Cape Cod Bay, Outer Cape, South Cape, Nantucket, Martha’s Vineyard, and South Coast west of Buzzards Bay is from 2013-2014 lidar data collected by the U.S. Geological Survey's (USGS) Coastal and Marine Geology Program. Shorelines were extracted from these lidar surveys using several different methods dependent on the location of the shoreline and whether or not wave data were available.
Supplemental_Information:
Cross-referenced citations are applicable to the dataset as a whole. Additional citations are located within individual process steps that pertain specifically to the method described in that step.
  1. How might this data set be cited?
    U.S. Geological Survey, 2018, Uncertainty table for lidar-derived shorelines used when calculating rates in the Digital Shoreline Analysis System software for the South Shore of MA: data release DOI:10.5066/P9O7S72B, U.S. Geological Survey, Coastal and Marine Geology Program, Woods Hole Coastal and Marine Science Center, Woods Hole, MA.

    Online Links:

    This is part of the following larger work.

    Himmelstoss, Emily A., Farris, Amy S., and Weber, Kathryn M., 2018, Massachusetts Shoreline Change Project: A GIS Compilation of Vector Shorelines for the 2018 update: data release DOI:10.5066/P9O7S72B, U.S. Geological Survey, Reston, VA.

    Online Links:

    Other_Citation_Details:
    Suggested citation: Himmelstoss, E.A., Farris, A.S., and Weber, K.M., 2018, Massachusetts shoreline change project—A GIS compilation of vector shorelines for the 2018 update: U.S. Geological Survey data release, https://doi.org/10.5066/P9O7S72B.
  2. What geographic area does the data set cover?
    West_Bounding_Coordinate: -70.8828788
    East_Bounding_Coordinate: -70.27291405
    North_Bounding_Coordinate: 42.30956215
    South_Bounding_Coordinate: 41.72377575
  3. What does it look like?
  4. Does the data set describe conditions during a particular time period?
    Calendar_Date: 10-Apr-2014
    Currentness_Reference:
    ground condition of the shorelines on which these values are basedX
  5. What is the general form of this data set?
    Geospatial_Data_Presentation_Form: tabular digital data
  6. How does the data set represent geographic features?
    1. How are geographic features stored in the data set?
      Indirect_Spatial_Reference:
      This dataset contains 4698 records that are related to the associated shoreline datasets by M-values in each polyline-M shapefile that is represented by the ID attribute in this dataset.
    2. What coordinate system is used to represent geographic features?
      Horizontal positions are specified in geographic coordinates, that is, latitude and longitude. Latitudes are given to the nearest 0.0197422321. Longitudes are given to the nearest 0.0262000699. Latitude and longitude values are specified in Decimal seconds. The horizontal datum used is WGS_1984.
      The ellipsoid used is WGS_84.
      The semi-major axis of the ellipsoid used is 6378137.0.
      The flattening of the ellipsoid used is 1/298.257223563.
  7. How does the data set describe geographic features?
    SouthShore_pShoreline_uncertainty
    uncertainty table (Source: U.S. Geological Survey)
    OID
    Internal feature number. (Source: Esri) Sequential unique whole numbers that are automatically generated.
    ID
    This field is case-sensitive and name specific. The field contains a cross-shore lidar profile ID stored as the M-value (measure value) at each vertex in the calibrated shoreline route. This serves as the link between the lidar shoreline and the uncertainty table and must be a unique number at each point. (Source: U.S. Geological Survey)
    Range of values
    Minimum:0
    Maximum:5525
    UNCY
    This field heading is case-sensitive and name specific. The field contains the plus/minus horizontal uncertainty (meters) in the lidar shoreline position at each cross-shore beach profile. (Source: U.S. Geological Survey)
    Range of values
    Minimum:0.27
    Maximum:14.8
    Units:meters
    BIAS
    This field heading is case-sensitive and name specific. The field contains a proxy-datum bias value describing the unidirectional horizontal offset (in meters) between the MHW elevation of the lidar data and proxy-based historic HWL shoreline positions. (Source: U.S. Geological Survey)
    Range of values
    Minimum:5.91
    Maximum:10.65
    Units:meters
    UNCYB
    This field heading is case-sensitive and name specific. The field contains the uncertainty in the calculated proxy-datum bias value (BIAS) in meters. (Source: U.S. Geological Survey)
    Range of values
    Minimum:3.456
    Maximum:7.354
    Units:meters
    Entity_and_Attribute_Overview:
    The entity and attribute information provided here describes the tabular data associated with the dataset. Please review the individual attribute descriptions for detailed information.
    Entity_and_Attribute_Detail_Citation: U.S. Geological Survey

Who produced the data set?

  1. Who are the originators of the data set? (may include formal authors, digital compilers, and editors)
    • U.S. Geological Survey
  2. Who also contributed to the data set?
  3. To whom should users address questions about the data?
    U.S. Geological Survey
    Attn: Emily A. Himmelstoss
    384 Woods Hole Road
    Woods Hole, MA
    USA

    508-548-8700 x2262 (voice)
    508-547-2310 (FAX)
    ehimmelstoss@usgs.gov

Why was the data set created?

This table includes: measurement and positional errors associated with the 2011 and 2013-2014 lidar shoreline for the South Shore of Massachusetts, a proxy-datum bias value that corrects for the unidirectional offset between the mean high water (MHW) elevation of the lidar and other high water line (HWL) shorelines, as well as a measurement uncertainty in the total water level.
The dataset contains a common attribute with the M-values stored for the lidar data within the SouthShore_pShoreline_2011.shp and SouthShore_pShoreline_2013_14.shp. These data are used in conjunction with the shoreline files to calculate rates of shoreline change.

How was the data set created?

  1. From what previous works were the data drawn?
    2011 lidar (source 1 of 2)
    Department of Commerce (DOC), National Oceanic and Atmospheric Administration (NOAA), National Ocean Service (NOS), Office for Coastal Management (OCM), 20120329, 2011 U.S. Geological Survey Topographic LiDAR: LiDAR for the North East: NOAA's Ocean Service, Office for Coastal Management (OCM), Charleston, SC.

    Online Links:

    Type_of_Source_Media: online
    Source_Contribution:
    The bare earth point cloud data in LAS format were used to extract shorelines using methods described in the process steps.
    2013-2014 lidar (source 2 of 2)
    Department of Commerce (DOC), National Oceanic and Atmospheric Administration (NOAA), National Ocean Service (NOS), Office for Coastal Management (OCM), and Woolpert, 20150615, 2013-2014 U.S. Geological Survey CMGP LiDAR: Post Sandy (MA, NH, RI): NOAA's Ocean Service, Office for Coastal Management (OCM), Charleston, SC.

    Online Links:

    Type_of_Source_Media: online
    Source_Contribution:
    The bare earth point cloud data in LAS format were used to extract shorelines using methods described in the process steps.
  2. How were the data generated, processed, and modified?
    Date: 2016 (process 1 of 4)
    Whenever possible, a profile method was used to extract the operational Mean High Water (MHW) shoreline from the lidar point cloud data, using a Matlab-based approach (Matlab version 2015b) similar to the one developed by Stockdon and others (2002). Elevation values for the height of MHW were determined from vdatum (version 3.8) provided by NOAA (https://vdatum.noaa.gov/). We continued the practice set out by Weber and others, (2005) of using one MHW value for a continuous section of coast (as opposed to using a continuously varying value). We chose this value such that it is always within 15 cm of the value returned by vdatum at any point along the coast. For example, we used MHW = 0.6 m for all of Buzzards Bay even though vdatum shows it varying slightly over the basin. For the shorelines of the South Shore of Massachusetts, we used an average MHW elevation of 1.22 meters. This profile method uses a coast-following reference line with 20 m spaced profiles. All lidar data points that are within 1 m of each profile are associated with that profile. All work is done on the 2 m wide profiles, working on a single profile at a time.
    For each profile, a linear regression was fit through data points on the foreshore and the regression was evaluated at the MHW elevation to yield the cross-shore position of the MHW shoreline. If there was a data gap at MHW or if the MHW elevation was obscured by water points, the linear regression was simply extrapolated to the MHW elevation. Foreshore beach slope is defined as the slope of the regression line.
    Each MHW shoreline point that was extracted using this profile method has an uncertainty associated with it. This uncertainty includes three components: 1) the 95% confidence interval on the linear regression estimate of the shoreline position; 2) the uncertainty associated with the elevation of the raw lidar data and; 3)the uncertainty due to extrapolation. These three components of uncertainty were added in quadrature to yield a total error for each shoreline point. For details on each component, see pp.12-13 under the section titled Lidar-Derived MHW Shoreline Position Uncertainty in Hapke and others (2011).
    There is a known horizontal offset between the datum-based lidar MHW shoreline and the proxy-based historical shorelines that nearly always acts in one direction (Ruggiero and List, 2009). Wave data from offshore buoys is used with the beach slope in a run-up equation to estimate a proxy-datum bias correction to reconcile the unidirectional offset that the proxy-based historic High Water Line (HWL) shorelines, such as those derived from NOAA t-sheets or air photos, have in relationship to the lidar-derived, datum-based operational MHW line. An uncertainty associated with the bias was also computed, which can also be thought of as the uncertainty of the HWL shorelines due to water level fluctuations. For details on the proxy-datum bias and bias uncertainty, see pp.9-11 under the section titled The Proxy-Datum Bias Correction between HWL and MHW Shorelines in Hapke and others (2011).
    Hapke, C.J., Himmelstoss, E.A., Kratzmann, M.G., List, J.H., and Thieler, E.R., 2011, National assessment of shoreline change—Historical shoreline change along the New England and Mid-Atlantic coasts: U.S. Geological Survey Open-File Report 2010-1118, 57 p., https://pubs.usgs.gov/of/2010/1118/.
    Ruggiero, P., and List, J.H., 2009, Improving accuracy and statistical reliability of shoreline position and change rate estimates: Journal of Coastal Research, v. 25, no. 5, p. 1069-1081. [Also available at https://www.jstor.org/stable/27752753]
    Stockdon, H.F., Sallenger, A.H., List, J.H., and Holman, R.A., 2002, Estimation of shoreline position and change using airborne topographic lidar data: Journal of Coastal Research, v.18, no. 3, p. 502-513. [Also available at https://www.jstor.org/stable/4299097] Person who carried out this activity:
    Amy S. Farris
    U.S. Geological Survey
    384 Woods Hole Road
    Woods Hole, MA
    USA

    508-548-8700 x2344 (voice)
    508-457-2310 (FAX)
    afarris@usgs.gov
    Date: 2016 (process 2 of 4)
    The series of operational MHW points extracted from the cross-shore lidar profiles were converted to a .dbf file storing the lidar positional uncertainty, for each point of the original lidar data. During the rate calculation process DSAS uses linear referencing to retrieve the uncertainty value stored in the associated table. Person who carried out this activity:
    Emily A. Himmelstoss
    U.S. Geological Survey
    384 Woods Hole Road
    Woods Hole, MA
    USA

    508-548-8700 x2262 (voice)
    508-457-2310 (FAX)
    ehimmelstoss@usgs.gov
    Date: 11-Jun-2020 (process 3 of 4)
    Moved the uncertainty table and the corresponding metadata to a landing page of its own to facilitate the assigning of a persistent identifier to the metadata that is based on the landing page UUID. This reorganization required updating various links in the metadata. Person who carried out this activity:
    U.S. Geological Survey
    Attn: VeeAnn A. Cross
    Marine Geologist
    384 Woods Hole Road
    Woods Hole, MA

    508-548-8700 x2251 (voice)
    508-457-2310 (FAX)
    vatnipp@usgs.gov
    Date: 10-Aug-2020 (process 4 of 4)
    Added keywords section with USGS persistent identifier as theme keyword. Person who carried out this activity:
    U.S. Geological Survey
    Attn: VeeAnn A. Cross
    Marine Geologist
    384 Woods Hole Road
    Woods Hole, MA

    508-548-8700 x2251 (voice)
    508-457-2310 (FAX)
    vatnipp@usgs.gov
  3. What similar or related data should the user be aware of?
    Thieler, E.R., and Smith, T.L., 2013, Massachusetts Shoreline Change Mapping and Analysis Project, 2012 Update: Open-File Report 2012-1189, U.S. Geological Survey, Reston, VA.

    Online Links:

    Smith, Theresa L., Himmelstoss, Emily A., and Thieler, E. Robert, 2013, Massachusetts Shoreline Change Project: A GIS Compilation of Vector Shorelines and Associated Shoreline Change Data for the 2012 update: Open-File Report 2012-1183, U.S. Geological Survey, Reston, VA.

    Online Links:

    Thieler, E. Robert, O'Connell, James F., and Schupp, Courtney A., 2001, The Massachusetts Shoreline Change Project: 1800s to 1994 Technical Report: U.S. Geological Survey, Coastal and Marine Geology Program, Woods Hole Coastal and Marine Science Center, Woods Hole, MA.

    Online Links:

    Himmelstoss, Emily A., Kratzmann, Meredith G., Hapke, Cheryl J., Thieler, E. Robert, and List, Jeffrey, 20110119, The National Assessment of Shoreline Change: A GIS Compilation of Vector Shorelines and Associated Shoreline Change Data for the New England and Mid-Atlantic Coasts: Open-File Report 2010-1119, U.S. Geological Survey, Reston, VA.

    Online Links:

    Himmelstoss, Emily A., Farris, Amy S., Henderson, Rachel E., Kratzmann, Meredith G., Ergul, Ayhan, Zhang, Ouya, and Zichichi, Jessica L., 2018, Digital Shoreline Analysis System (version 5.0): U.S. Geological Survey software: software release version 5.0, U.S. Geological Survey, Reston, VA.

    Online Links:


How reliable are the data; what problems remain in the data set?

  1. How well have the observations been checked?
    The attributes in this table record positional and measurement uncertainties and datum offsets calculated during the process of extracting an operational mean high water shoreline from the lidar data as described in the process steps. The field names are based on the requirements for use within the Digital Shoreline Analysis System (DSAS) software (USGS software release).
  2. How accurate are the geographic locations?
    Each MHW shoreline point extracted using the profile method has an uncertainty associated with it. This uncertainty includes three components:
    1) the 95% confidence interval on the linear regression estimate of the shoreline position;
    2) the uncertainty associated with the elevation of the raw lidar data which is stated as 0.1 m RMS in the lidar metadata;
    3) the uncertainty due to extrapolation if the shoreline point was determined by extrapolation.
    These three components of uncertainty were then added in quadrature, yielding a total error for each shoreline point which is stored in the shoreline uncertainty DBF file associated with these data.
    The lidar shorelines have an average positional uncertainty of plus or minus 2.03 meters.
  3. How accurate are the heights or depths?
  4. Where are the gaps in the data? What is missing?
    The table only contains data where a mean high water shoreline point could be extrapolated from the lidar.
  5. How consistent are the relationships among the observations, including topology?
    Each row contains data associated with an individual vertex point along the lidar shoreline in SouthShore_pShoreline_2011.shp and SouthShore_pShoreline_2013_14.shp.

How can someone get a copy of the data set?

Are there legal restrictions on access or use of the data?
Access_Constraints: None.
Use_Constraints:
Public domain data from the U.S. Government are freely redistributable with proper metadata and source attribution. Please recognize the U.S. Geological Survey as the originator of the dataset.
  1. Who distributes the data set? (Distributor 1 of 1)
    U.S. Geological Survey - ScienceBase
    MS 302
    Denver, CO
    USA

    1-888-275-8747 (voice)
    sciencebase@usgs.gov
  2. What's the catalog number I need to order this data set? The dataset contains the uncertainty data in DBF format (SouthShore_pShoreline_uncertainty.dbf) and the CSDGM metadata in XML and TEXT format.
  3. What legal disclaimers am I supposed to read?
    Neither the U.S. Government, the Department of the Interior, nor the USGS, nor any of their employees, contractors, or subcontractors, make any warranty, express or implied, nor assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, nor represent that its use would not infringe on privately owned rights. The act of distribution shall not constitute any such warranty, and no responsibility is assumed by the USGS in the use of these data or related materials.
    Any use of trade, product, or firm names is for descriptive purposes only and does not imply endorsement by the U.S. Government.
  4. How can I download or order the data?
  5. What hardware or software do I need in order to use the data set?
    These data are available in dBase file format. The user must have software capable of reading or importing the dBase formatted data file.

Who wrote the metadata?

Dates:
Last modified: 10-Aug-2020
Metadata author:
Emily A. Himmelstoss
U.S. Geological Survey
384 Woods Hole Road
Woods Hole, MA
USA

508-548-8700 x2262 (voice)
508-457-2310 (FAX)
ehimmelstoss@usgs.gov
Metadata standard:
FGDC Content Standards for Digital Geospatial Metadata (FGDC-STD-001-1998)

This page is <https://cmgds.marine.usgs.gov/catalog/whcmsc/SB_data_release/DR_P9O7S72B/SouthShore_pShoreline_uncertainty.dbf.faq.html>
Generated by mp version 2.9.50 on Tue Sep 21 18:19:10 2021